manualshive.com logo in svg

Kikusui BIM1000 Series, User Manual

Share
Download
Kikusui BIM1000 Series User Manual Download Page 2

2

User’s Manual

BIM1000 Series

This manual provides an overview of the product and 
notes on usage. It also explains how to configure it, oper-
ate it, perform maintenance on it, and so on. Read this 
manual thoroughly before use, and use the product prop-
erly.

Intended readers

These manuals are intended for users of this product and 
their instructors. The manuals assume that the reader has 
knowledge about electric safety testing.

Manual construction

• User’s manual 

 (this manual)

This document is intended for first-time users of this 
product. It provides an overview of the product, notes on 
usage, and specifications. It also explains how to con-
nect the product, configure the product, operate the 
product, perform maintenance on the product, and so 
on.

• Safety Information 

 

This document contains general safety precautions. 
Keep them in mind and make sure to observe them.

• Packing list 

 

The packing list shows the included accessories.

PDF files are included in the accompanying CD-ROM. You 
can view the PDF files using Adobe Reader.

Software versions that this guide covers

This manual covers firmware versions 1.0X.
The firmware version is shown in the top area of the sys-
tem setting screen, which can be displayed by pressing 
SYSTEM.
When contacting us about the product, please provide us 
with:

The model (marked in the top section of the front panel)
The firmware version
The serial number (marked on the rear panel)

Trademarks

All company names and product names used in this man-
ual are trademarks or registered trademarks of their 
respective companies.

Copyright

Reproduction and reprinting of this operation manual, 
whole or partially, without our permission is prohibited.
Both unit specifications and manual contents are subject to 
change without notice.
© Copyright 2019 Kikusui Electronics Corporation

About Manuals

PDF

PDF

Paper

Paper

PDF

PDF

Paper

Paper

PDF

PDF

Accessories

Power cord (1 pc., length: approx. 2.5 m)

CD-ROM (1 disc)

Safety Information (1 copy)

Plug: CEE7/7
Rating: 250 Vac/10 A 
[85-10-1070]

Plug: GB1002
Rating: 250 Vac/10 A 
[85-10-0791]

or

or

The attached power cord varies depending on the shipment destination.

Plug: NEMA5-15
Rating: 125 Vac/10 A
[85-AA-0003]

Packing list (1 copy)

Summary of Contents for BIM1000 Series































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands