Keysight N5247-60106 Installation Note Download Page 12

Page: 12 / 54

12 Installation Note N5247-90106

Items Included in the Upgrade Kit

W106

RF cable, A39 port 3 source attenuator to front-panel Port 3 SOURCE OUT

N5247-20009

W107

RF cable, A43 port 3 bias tee to port 3 CPLR THRU

N5247-20010

W108

RF cable, A43 port 3 bias tee to A34 port 3 coupler

N5247-20028

W109

RF cable, A31 port 4 reference coupler to A40 port 4 source attenuator

N5247-20083

W110

RF cable, A40 port 4 source attenuator to front-panel Port 4 SOURCE OUT

N5247-20025

W111

RF cable, port 4 CPLR THRU to A44 port 4 bias tee

N5247-20021

W112

RF cable, A44 port 4 bias tee to A35 port 4 coupler

N5247-20029

W116

RF cable, A45 port 2 bias tee to A36 port 2 coupler

N5247-20080

W119

RF cable, port 3 RCVR C IN to A47 port 3 receiver attenuator

N5247-20008

W120

RF cable, A47 port 3 receiver attenuator to A28 mixer brick (C)

N5247-20064

W121

RF cable, Port 4 RCVR D IN to A48 port 4 receiver attenuator

N5247-20024

W122

RF cable, A48 port 4 receiver attenuator to A28 mixer brick (D)

N5247-20065

W144

RF cable, A29 port 1 reference coupler to A37 reference mixer switch

N5247-20071

W145

RF cable, REF 2 RCVR R2 IN to A27 mixer brick (R2)

N5247-20066

Ribbon cable, A23 test set motherboard J547 to A39 port 3 source

attenuator

N5245-60006

Ribbon cable, A23 test set motherboard J548 to A40 port 4 source

attenuator

Ribbon cable, A23 test set motherboard J5 to A61 port 3 70 GHz doubler

N5247-60018

Ribbon cable, A23 test set motherboard J3 to A62 port 4 70 GHz doubler

Ribbon cable, A23 test set motherboard J206 to A47 port 3 receiver

attenuator

N5247-60020

Ribbon cable, A23 test set motherboard J207 to A48 port 4 receiver

attenuator

Ribbon cable, A23 test set motherboard J552 to A28 mixer brick (2) J52

N5247-60015

Wire harness, A43 port 3 bias tee to A23 test set motherboard J543

N5247-60021

Wire harness, A44 port 4 bias tee to A23 test set motherboard J544

Table 1

Contents of Upgrade Kit N5247-90106

Ref

Desig.

Description

Qty

Part Number

Summary of Contents for N5247-60106























































Search results

Summary of Contents for N5247-60106

Reviews:

Related manuals for N5247-60106

Brands by name

Popular brands

Keysight N5247-60106, Installation Note

Search results

Summary of Contents for N5247-60106

Reviews:

Related manuals for N5247-60106

Brands by name

Popular brands