Keysight N5247-60106 Installation Note Download Page 37 | Manualshive

Page: 37 / 54

background image

Installation Note N5247-90106 37

Installation Procedure for the Upgrade

Figure 23

A33 - A36 Test Port Coupler Assembly

Step 36. Remove and Disassemble the 2-Port Test Set Front Plate

1. Remove two screws from each LED board and remove the boards from the

2-port test set front plate of the PNA. Keep the screws for reinstallation

later.

2. Remove the 2-port test set front plate from the test set deck. Keep the

screws to reuse later.

3. Remove the 12 bulkhead connectors, nuts and washers from the 2-port

front plate to reuse later.

«
...
35
36
37
38
39
...
»

Summary of Contents for N5247-60106























































Reviews:

No comments

Related manuals for N5247-60106

Masoneilan 12400 Series

Brand: Baker Hughes Pages: 81

Brand: Parr Instrument Pages: 110

Brand: FARMSCAN Pages: 28

Brand: Keithley Pages: 138

Brand: IFM Pages: 2

Brand: Xtralis Pages: 13

Brand: Tektronix Pages: 124

Brand: Polimaster Pages: 6

Brand: STONEX Pages: 99

Brand: Kipp & Zonen Pages: 32

Brand: Omega Pages: 20

miniSERIES Series

Brand: Valeport Pages: 25

Seeker 400 Series

Brand: General Pages: 24

Brand: shelyak Pages: 45

Brand: Vega Pages: 44

Brand: S&T Pages: 23

Brand: D-tect Systems Pages: 28

Radon Scout Home

Brand: SARAD Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands