Keysight N5247-60106 Installation Note Download Page 45

Page: 45 / 54

Installation Note N5247-90106 45

Installation Procedure for the Upgrade

Figure 29

Location of Cable Tie to Secure W144

— W51 (reuse) (N5247-20011) A37 reference mixer switch to REF 1 SOURCE

OUT

— W52 (reuse) (N5247-20012) A37 reference mixer switch to REF 1 RCVR R1

— W53 (reuse) (N5247-20048) A37 reference mixer switch to A27 mixer brick

(R1)

— W118 (reuse) (N5247-20047) A46 port 1 receiver attenuator to A27 mixer

brick (A )

— W122 (N5247-20065) A48 port 4 receiver attenuator to A28 mixer brick (D)
— W101 (reuse) (N5247-20083) A29 port 1 reference coupler to A38 port 1

source attenuator

— W113 (reuse) (N5247-20083) A32 port 2 reference coupler to A41 port 2

source attenuator

— W105 (N5247-20083) A30 port 3 ref coupler to A39 port 3 source

attenuator

— W109 (N5247-20083) A31 port 4 ref coupler to A40 port 4 source

attenuator

— W27 (reuse) (N5247-20044) A60 port 1 70 GHz doubler to A29 port 1

reference coupler

— W16 (N5247-20060) A61 port 3 70 GHz doubler to W15

Summary of Contents for N5247-60106























































Search results

Summary of Contents for N5247-60106

Reviews:

Brands by name

Popular brands

Keysight N5247-60106, Installation Note

Search results

Summary of Contents for N5247-60106

Reviews:

Brands by name

Popular brands