manualshive.com logo in svg

Keysight N5247-60106, Installation Note

Share
Download
Keysight N5247-60106 Installation Note Download Page 11

Installation Note N5247-90106                                                                                                                                  11

Items Included in the Upgrade Kit

W38

RF cable, A34 port 3 coupler to front-panel Port 3 CPLR ARM

1

N5247-20007

W41

RF cable, A31 port 4 ref coupler to front-panel REF 4 SOURCE OUT

1

N5247-20069

W42

RF cable, A35 port 4 coupler to front-panel Port 4 CPLR ARM

1

N5247-20026

W46

RF cable, A36 port 2 coupler to front-panel port 2 CPLR ARM 

1

N5247-20019

W54

RF cable, REF 3 RCVR R3 IN to A28 mixer brick (R3)

1

N5247-20062

W55

RF cable, REF 4 RCVR R4 IN to A28 mixer brick (R4)

1

N5247-20067

W58

RF cable, 2.4 mm cap for A28 mixer brick

1

N5247-20138

W60

RF cable, front panel jumper

6

N5247-20107

W62

RF cable, A25 HMA26.5 to A26 splitter

1

N5247-20111

W63

RF cable, A26 splitter to A27 mixer brick

1

N5245-20023

W64

RF cable, A26 splitter to A28 mixer brick

1

N5245-20022

W67

RF cable, A12 port 3 40 GHz doubler P5 to W68

1

N5247-20096

W68

RF cable, rear-panel port RF2 OUT (J12) to W67

1

N5247-20088

W72

RF cable, A27 mixer brick (R1) to A24 IF multiplexer (P411)

1

N5242-60021

W73

RF cable, A27 mixer brick (R2) to A24 IF multiplexer (P412)

1

N5242-60022

W75

RF cable, A28 mixer brick (D) to A24 IF multiplexer (P801)

1

N5242-60024

W76

RF cable, A28 mixer brick (R4) to A24 IF multiplexer (P414)

1

N5242-60019

W77

RF cable, A28 mixer brick (R3) to A24 IF multiplexer (P413)

1

N5242-60020

W78

RF cable, A28 mixer brick (C) to A24 IF multiplexer (P601)

1

N5242-60023

W80

RF cable, A24 IF multiplexer board P203 to A16 SPAM board J2

1

N5242-60013

W82

RF cable, A24 IF multiplexer board P603 to A16 SPAM board J5

1

N5242-60015

W87

RF cable, A14 frequency ref (J7) to A17 13.5 GHz (source 2) synth (J5)

1

N5242-60030

W93

RF cable, A61 port 3 70 GHz dblr J2 to A12 40 GHz dblr J401 

1

N5247-60010

W94

RF cable, A61 port 3 70 GHz dblr J4 to A12 40 GHz dblr J500 

1

N5247-60011

W95

RF cable, A62 port 4 70 GHz doubler (J2) to A13 40 GHz doubler (J401)

1

N5247-60012

W96

RF cable, A62 port 4 70 GHz dblr J4 to A13 40 GHz dblr J500

1

N5247-60013

W103

RF cable, front-panel Port 1 CPLR THRU to A42 port 1 bias tee

1

N5247-20081

W104

RF cable, A33 port 1 coupler to A42 port 1 bias tee

1

N5247-20022

W105

RF cable, A30 port 3 reference coupler to A39 port 3 source attenuator

1

N5247-20083

Table 1 

Contents of Upgrade Kit N5247-90106

Ref 

Desig.

Description

Qty

 Part Number

Summary of Contents for N5247-60106























































Reviews:

No comments

Brands by name

Popular brands

Load more brands