manualshive.com logo in svg

Keysight N5247-60106, Installation Note

Share
Download
Keysight N5247-60106 Installation Note Download Page 19

Installation Note N5247-90106                                                                                                                                  19

Installation Procedure for the Upgrade

Step 10. Remove the A60 70 GHz Doubler Assembly From the Test 

Set Deck

Remove the 70 GHz doubler 1 assembly from the test set deck. For 

instructions, click the Chapter 7 bookmark, “Removing and Replacing the 
A60-A63 70 GHz Doublers” in the PDF Service Guide

1

. Keep all parts for 

reinstallation later.

Step 11. Assemble the A61 70 GHz Doubler on the Doubler Mount

1.

Follow the instruction in 

Figure 3

 to install the A61 70 GHz doubler 3 on 

the doubler mount. New parts are listed in 

Table 1 on page 8

 of this 

document.

Figure 3 

Installing A61 Doubler 3 on the Doubler Mount

2.

Connect the cables to the A61 70 GHz doubler 3 in the order shown in 

Figure 4

. The other ends of the cables will be connected later.

Summary of Contents for N5247-60106























































Reviews:

No comments

Brands by name

Popular brands

Load more brands