Keysight N5247-60106 Installation Note Download Page 8

Page: 8 / 54

8 Installation Note N5247-90106

Items Included in the Upgrade Kit

Check the contents of your kit against the following lisst. If any part is missing

or damaged, contact Keysight Technologies. Refer to

“Getting Assistance from

Keysight” on page 4

Table 1

Contents of Upgrade Kit N5247-90106

Ref

Desig.

Description

Qty

Part Number

Installation note (this document)

N5247-90106

A10

26.5 GHz source (2) board

5087-7780

A12

40 GHz doubler assembly port 3

5087-7346

A13

40 GHz doubler assembly port 4

A17

13.5 GHz (source 2) synthesizer board

N5240-60074

A26

Splitter

5067-4086

A28

Mixer brick (2)

5087-7337

A30

Test port 3 reference coupler

5087-7744

A31

Test port 4 reference coupler

A34

Test port 3 coupler

5087-7778

A35

Test port 4 coupler

A39

Test port 3 source attenuator

84905-60004

A40

Test port 4 source attenuator

A43

Test port 3 bias tee

5087-7732

A44

Test port 4 bias tee

A47

Test port 3 receiver attenuator

84905-60004

A48

Test port 4 receiver attenuator

A61

Test port 3 70 GHz doubler assembly

5087-7336

A62

Test port 4 70 GHz doubler assembly

A69

3 dB pad, attached to R4 connector on A28 mixer brick

08490-60037

Front frame, 4-port

N5247-20141

Bulkhead connector, front panel

5065-4673

Washer for bulkhead connectors, front panel

1250-3310

Nut for bulkhead connectors, front panel

1250-3516

Machine screw, M2.0 x 6, pan head (8 to attach 2 reference couplers to

brackets)

0515-0658

Summary of Contents for N5247-60106























































Search results

Summary of Contents for N5247-60106

Reviews:

Related manuals for N5247-60106

Brands by name

Popular brands

Keysight N5247-60106, Installation Note

Search results

Summary of Contents for N5247-60106

Reviews:

Related manuals for N5247-60106

Brands by name

Popular brands