Keysight N5247-60106 Installation Note Download Page 51

Page: 51 / 54

Installation Note N5247-90106 51

Installation Procedure for the Upgrade

Step 53.Remove Option 219 License

Procedure Requirements

— The analyzer must be powered up and operating to perform this procedure.
— The Network Analyzer program must be running.
— A keyboard and mouse must be connected to the network analyzer.

Option 219 License Removal Procedure

To start the option enable utility, press UTILITY

, then

then

. An option enable dialog box will appear.

2. Click the arrow in the

Select Desired Option

box. A list of available options

will appear.

3. In the

Select Desired Option

list, click

219

4. Click

Remove

5. Click OK to confirm that you want to remove the license for the selected

option.

Click

Yes

in answer to the displayed question in the

Restart Analyzer?

box.

Step 54. Enable Options P04 (400) and 419

Procedure Requirements

- The analyzer must be powered up and operating to perform this procedure.
- The Network Analyzer program must be running.

A keyboard and mouse must be connected to the network analyzer.

Option Enable Procedure

1. To start the option enable utility, press UTILITY

, then

then

. An option enable dialog box will appear.

2. Click the arrow in the

Select Desired Option

box. A list of available options

will appear.

3. In the

Select Desired Option

list, click

P04 - 4-Ports

4. Using the keyboard, enter the license key in the box provided. The license

key is printed on the license message you received from Keysight. Enter

this key

exactly

as it is printed on the message.

5. Click

Enable

6. Click

Yes

in answer to the displayed question in the

Restart Analyzer?

box.

System

Service

Option Enable

System

Service

Option Enable

Summary of Contents for N5247-60106























































Search results

Summary of Contents for N5247-60106

Reviews:

Related manuals for N5247-60106

Brands by name

Popular brands

Keysight N5247-60106, Installation Note

Search results

Summary of Contents for N5247-60106

Reviews:

Related manuals for N5247-60106

Brands by name

Popular brands