manualshive.com logo in svg

Keysight N5247-60106, Installation Note

Share
Download
Keysight N5247-60106 Installation Note Download Page 20

 20                                                                                                                               Installation Note N5247-90106

Installation Procedure for the Upgrade

-

Figure 4 

A61 70 GHz Doubler Assembly

Step 12. Reinstall the A60/A61 70 GHz Doubler Assembly

Reinstall the A60 70 GHz doubler 1 cables, and then reinstall the A60/A61 70 

Ghz doubler assembly on the test set deck, reusing the existing screws. For 

instructions,

 

click the Chapter 7 bookmark, “Removing and Replacing the 

A60-A63 70 GHz Doublers” in the PDF Service Guide

1

.

Step 13. Remove the A63 70 GHz Doubler Assembly From the Test 

Set Deck

Remove the A63 70 GHz doubler 2 assembly from the test set deck. For 

instructions, click the Chapter 7 bookmark, “Removing and Replacing the 
A60-A63 70 GHz Doublers” in the PDF Service Guide

1

. Keep all parts for 

reinstallation later.

Step 14. Assemble the A62 70 GHz Doubler on the Doubler Mount

1.

Follow the instruction in 

Figure 5

 to install the A62 70 GHz doubler 4 on 

the doubler mount. New parts are listed in 

Table 1 on page 8

 of this 

document.

1. See 

“Downloading the Online PNA Service Guide” on page 6

.

Summary of Contents for N5247-60106























































Reviews:

No comments

Brands by name

Popular brands

Load more brands