Keysight Infiniium 8000 Series Service Manual Download Page 114

Page: 114 / 162

Chapter 6: Replacing Assemblies
To remove and replace the keyboard, touch screen, and flat-panel display assemblies

114

To remove the main keyboard assembly, disconnect the cursor keyboard
interconnect cable, pull off the knobs, and lift out the keyboard.

Figure 6-19

Removing the keyboard

To remove the touch screen assembly from the front- panel cover plate, remove
the six T8 Torx fasteners.

To remove the flat- panel display assembly, remove the backlight inverter board
(see page 107), then remove the four T8 Torx fasteners.

Figure 6-20

Removing the touch screen and flat-panel display

Main keyboard

Knobs

Label

Keypad

Cursor keyboard
interconnect
cable

Front-panel
cover plate

Flat-panel display

Touch screen
assembly

Summary of Contents for Infiniium 8000 Series


































































































































































Search results

Summary of Contents for Infiniium 8000 Series

Reviews:

Related manuals for Infiniium 8000 Series

Brands by name

Popular brands

Keysight Infiniium 8000 Series, Service Manual

Search results

Summary of Contents for Infiniium 8000 Series

Reviews:

Related manuals for Infiniium 8000 Series

Brands by name

Popular brands