Keysight Technologies U3047AM08 User'S And Service Manual Download Page 65

Page: 65 / 92

U3047AM08
Service Information

The following replaceable parts may be ordered by sending an e-mail request
to [email protected]. Be sure to include test set model, options
and serial number. Some parts may have long lead times.

Table 1

Replaceable Parts (M08)

Description

Keysight

Part Number

Screw-Pan Head Machine with thread patch, Torx-T15 M3.5

with 0.6 thread, 12 mm-LG

0515-2317

2.4 mm Short (female)

85056-60021

Dress Nut (couplers)

N5230-20081

Test Set Rear Lock Feet (right)

N5242-20138

Test Set Rear Lock Feet (left)

N5242-20139

Front Panel LED Board (programmed)

N5261-60005

Test Set Control Board (programmed)

N5261-60006

DUT Control Board

U3020-63223

SW Interface Board 25 V, programmed

U3025-60068

U3047AM08 User’s and Service Guide

U3047-90004

RF Cable, Semi-rigid

U3047-20016

RF Cable, Semi-rigid

U3047-20017

Keysight U3047AM08 User's and Service Guide

Summary of Contents for U3047AM08





























































































Search results

Summary of Contents for U3047AM08

Reviews:

Related manuals for U3047AM08

Brands by name

Popular brands

Keysight Technologies U3047AM08, User'S And Service Manual

Search results

Summary of Contents for U3047AM08

Reviews:

Related manuals for U3047AM08

Brands by name

Popular brands