Keysight Technologies U3047AM08 User'S And Service Manual Download Page 12

Page: 12 / 92

U3047AM08
General Specifications

Maximum Power Levels

Table

Instrument Dimensions

Model

Weight

Height

Wid th

Depth

U3047AM08

13.6 kg (30 lb)

19 cm

(7.5 in)

42.5 cm

(16.7 in)

50 cm

(20 in)

It is recommended that you do not operate components near damage

levels (+28 dBm).

Do not apply any DC voltage to any front panel ports.

The power levels must be 3 dB below maximum level to ensure no

damage.

see

Table

below.

Table

Maximum Power Levels

Maximum Power Levels

U3047AM08 Test Port RF Power Levels:

PORT 5-12

+25 dBm

U3047AM08 Access Ports:

SOURCE OUT

+15 dBm

CPLR ARM

+15 dBm

CPLR THRU

+15 dBm

RCVR OUT

+15 dBm

Refer to your analyzer’s specifications to determine the maximum input

power levels for the access and test ports, or to optimize the power levels

in the receivers.

Damage and maximum levels are not necessarily the optimum level.

Keysight U3047AM08 User's and Service Guide

Summary of Contents for U3047AM08





























































































Search results

Summary of Contents for U3047AM08

Reviews:

Related manuals for U3047AM08

Brands by name

Popular brands

Keysight Technologies U3047AM08, User'S And Service Manual

Search results

Summary of Contents for U3047AM08

Reviews:

Related manuals for U3047AM08

Brands by name

Popular brands