Keysight Technologies U3047AM08 User'S And Service Manual Download Page 30 | Manualshive

Page: 30 / 92

background image

U3047AM08
Controlling the Test Set

Multiport Mode

The multiport mode selects the test set file that will enable the network
analyzer to control the test set. Multiport mode allows you to complete a
N-Port calibration using the Cal Wizard application in the network analyzer.

Refer to the Help system for more information.

How to Access Multiport Mode

1. The Option 551 must be installed for multiport capability. To access the

multiport application select
Utility > System > Configure > Multiport Capability -OR-

(Instrument > Setup > External Hardware > Multiport > Multiport
Configuration...)

.

2. Select U304xAM08_PNAX_p4 (12-Port System) from the drop-down menu

and select Restart as a multiport PNA with this test set > OK.

Figure 20

If the test set is not available in the drop-down list, it will be necessary for you
to copy the required test set file to the analyzer's hard drive. The current
version of the test set files are available on the web at

http://na.support.keysight.com/multiport/testsetsupport.html

appropriate file to

c:\program files\Keysight\Network Analyzer\testsets

directory.

Test Set Selection

30

Keysight U3047AM08 User's and Service Guide

«
...
28
29
30
31
32
...
»

Summary of Contents for U3047AM08





























































































Reviews:

No comments

Related manuals for U3047AM08

Brand: Varec Pages: 74

Brand: Halyard Pages: 84

Brand: PAIDI Pages: 48

Brand: DARKSTAR TECHNOLOGIES Pages: 4

Brand: TDW Pages: 2

Brand: Taurus Pages: 25

Brand: Vancare Pages: 3

Brand: Paitec Pages: 14

Brand: UNIA Pages: 62

Brand: R2 Pages: 20

Brand: Rain-Flo Irrigation Pages: 20

Attest Auto-reader 390

Brand: 3M Pages: 2

Brand: 3M Pages: 2

Brand: 3M Pages: 2

PELTOR WS LiteCom Plus

Brand: 3M Pages: 7

Steri-Vac GS Series

Brand: 3M Pages: 52

Brand: Qu-Bit Electronix Pages: 15

Brand: Velleman Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands