Keysight Technologies S9106AC-2IF Startup Manual Download Page 58

Page: 58 / 80

6 Verify Operation

6. 1 S9106AC-2IF: Detailed Steps to Verify Operation

Connect AC Power Cords & Power On Equipment

on page

Verify X-Apps Controls S9106AC-2IF RF Ports at 3 GHz

on page

Verify X-Apps Controls S9106AC-2IF High IF Ports at 10 GHz

on page

6. 1. 1 Connect AC Power Cords & Power On Equipment

1. Connect an AC Power Cord to the E7770A CIU right-rear panel.

2. Power on the E7770A CIU Rear Mains Switch, located on the right-rear panel.

3. Power on the E7770A CIU AC Power Switch, located on the left-front panel.

4. Connect an AC Power Cord to the S9106AC Base System right-rear panel.

5. Power on the S9106AC-2IF AC Power Switch, located on the left-front panel.

The M9037A PXIe Embedded Controller and the M9300A PXIe Reference are
part of the S9106AC Base System; they both power on and initialize
automatically when the S9106AC Base System is powered on.

S9106AC-2IF, -4UP, and -42D 5G FR1 Multi-port Transceiver Solutions, Startup Guide

Summary of Contents for S9106AC-2IF

















































































Search results

Summary of Contents for S9106AC-2IF

Reviews:

Related manuals for S9106AC-2IF

Brands by name

Popular brands

Keysight Technologies S9106AC-2IF, Startup Manual

Search results

Summary of Contents for S9106AC-2IF

Reviews:

Related manuals for S9106AC-2IF

Brands by name

Popular brands