Keysight Technologies S9106AC-2IF Startup Manual Download Page 19 | Manualshive

Page: 19 / 80

background image

2 Review Safety Requirements

S9106AC-2IF, -4UP, and -42D 5G FR1 Multi-port Transceiver Solutions, Startup Guide

15

2. 11 AC Power Cord

The Keysight S9106AC-2IF, -4UP, and -42D 5G FR1 Multi-port Transceiver Solutions
are equipped with three-wire power cords, in accordance with international safety
standards. These power cords ground the Keysight S9106AC-2IF, -4UP, and -42D
5G FR1 Multi-port Transceiver Solutions cabinet when connected to an appropriate
power line outlet.

Use the Keysight supplied power cord or one with the same or better electrical rating.
The cable appropriate to the original shipping location is included with the
Keysight S9106AC-2IF, -4UP, and -42D 5G FR1 Multi-port Transceiver Solutions.
See:

http://www.keysight.com/find/powercords

Always use the three-prong AC power cord supplied with these
products. Failure to ensure adequate earth grounding by not using
these cords can cause product damage.

If these products are not used as specified, the protection
provided by the equipment could be impaired. These products
must be used in a normal condition (in which all means for
protection are intact) only. Install the Keysight S9106AC-2IF, -
4UP, and -42D 5G FR1 Multi-port Transceiver Solutions so that its
detachable power cords are readily identifiable and easily
reached by the operator. The detachable power cord is the
instrument's disconnecting device. It disconnects the Mains
circuits from the Mains supply before other parts of the
instrument. The front panel switch is only a standby switch and is
not a LINE switch.
Alternatively, an externally installed switch or circuit breaker
(which is readily identifiable and is easily reached by the operator)
may be used as a disconnecting device.

«
...
17
18
19
20
21
...
»

Summary of Contents for S9106AC-2IF

















































































Reviews:

No comments

Related manuals for S9106AC-2IF

Brand: i-SENS Pages: 50

Brand: janitza Pages: 6

Brand: janitza Pages: 36

Brand: NARDA Pages: 64

Brand: bmcm Pages: 5

Brand: Tektronix Pages: 48

Brand: TSI Instruments Pages: 4

Brand: Ratek Pages: 24

Brand: Oldham Pages: 106

Brand: Osaka Pages: 3

Brand: SIKA Pages: 8

Brand: Bitzer Pages: 8

Brand: ABQ Industrial Pages: 32

Brand: Factair Pages: 38

Brand: A&D Pages: 23

Brand: B meters Pages: 30

Brand: Techcomp Pages: 51

ISOLGUARD HIG93

Brand: hakel Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands