Keysight Technologies S9106AC-2IF Startup Manual Download Page 32

Page: 32 / 80

3 Review Hardware

3. 2. 5 Connectors, M9037A PXIe Embedded Controller

Status LEDs

PWR (Green)

On, indicates power supply
to embedded controller is good.

SSD (Amber)

Flashes when Solid State Drive is active.

Link (Green)

Indicates PCIe Link status:
Off = No link;
Blinking @ 1 Hz = Gen1 speed
Blinking @ 2 Hz = Gen2 speed
On steady = Gen3 speed

LAN (White),
USR (Grey)

Both LEDs are reserved for Keysight use only.

Video/Dual Display Ports

Connectors

Two, Dual Mode Disp+ connectors can
support either a DisplayPort or DVI-D monitor

USB 2.0 and 3.0

Connectors

Four, USB 2.0 (Type A)

Connectors

Two, USB 3.0

LAN 1 and LAN 2

Connectors

Two, 10/100/1000BASE-T
(RJ-45) Gigabit Ethernet ports

LAN Connector
Top LED (Amber)

LAN Connector
   Bottom LED (Off)
   Bottom LED (Green)
   Bottom LED (Amber)

LAN Connectors,
Top and Bottom
LEDs (Off)

Active, blinks if accessing IO

LAN Speed: 10 Mbps
LAN Speed: 100 Mbps
LAN Speed: 1000 Mbps

Network link not established
or system is powered off.

LAN RST (Reset) Button

Reserved for Keysight use only.

Trig (PXI Trigger In/Out)

Connector

SMB (m) snap-on,
bi-directional trigger connector for routing an
external trigger signal to/from PXI backplane

GPIB

Connector

GPIB (Micro-D 25-pin)

PCIe

Connector

x8 Gen 3 PCIe IPASS connector for controlling
a second PXIe or AXIe chassis or RAID storage

S9106AC-2IF, -4UP, and -42D 5G FR1 Multi-port Transceiver Solutions, Startup Guide

Summary of Contents for S9106AC-2IF

















































































Search results

Summary of Contents for S9106AC-2IF

Reviews:

Related manuals for S9106AC-2IF

Brands by name

Popular brands

Keysight Technologies S9106AC-2IF, Startup Manual

Search results

Summary of Contents for S9106AC-2IF

Reviews:

Related manuals for S9106AC-2IF

Brands by name

Popular brands