Keysight Technologies S9106AC-2IF Startup Manual Download Page 16 | Manualshive

Page: 16 / 80

background image

2 Review Safety Requirements

2. 9. 1 Before Applying Power

Verify that all safety precautions are taken. Make all connections to the unit before
applying power. Note the external markings described under

Front and Rear Panel

The Mains wiring and connectors shall be compatible with the
connector used in the premise electrical system. Failure to ensure
adequate earth grounding by not using the correct components
may cause product damage and serious injury.

2. 9. 2 Ground the Instrument

These products must be used in a normal condition (all means for
protection are intact).

This is a Safety Protection Class I Product (provided with a
protective earthing ground incorporated in the power cord). The
mains plug shall only be inserted in a socket outlet provided with a
protective earth contact. Any interruption of the protective
conductor inside or outside of the product is likely to make the
product dangerous. Intentional interruption is prohibited.

2. 9. 3 Power Strip Warning

DO NOT use a power strip which is not suitable for the installation.
These devices may not be sufficiently rated to carry the required
current and may become a safety hazard.

2. 9. 4 Do Not Use Extension Cords

DO NOT use extension cords to power your equipment.

2. 9. 5 Do Not Use Converters or Adapters

DO NOT use any converters or adapters.

12

S9106AC-2IF, -4UP, and -42D 5G FR1 Multi-port Transceiver Solutions, Startup Guide

«
...
14
15
16
17
18
...
»

Summary of Contents for S9106AC-2IF

















































































Reviews:

No comments

Related manuals for S9106AC-2IF

Brand: Kawai Pages: 2

Brand: Datron Pages: 197

Brand: Valor Pages: 13

Brand: Campbell Pages: 31

Charge Analyzer 711

Brand: 3M Pages: 24

NUFLO Scanner 2000 microEFM

Brand: Cameron Pages: 8

Brand: Garmin Pages: 120

Brand: Omicron Lab Pages: 33

Brand: Omicron Lab Pages: 21

Brand: Omicron Lab Pages: 22

Brand: Vectornav Pages: 114

Brand: Veeder-Root Pages: 59

Brand: Yamaha Pages: 84

Brand: Omega Pages: 24

Brand: Barksdale Pages: 2

Brand: TSI Instruments Pages: 4

Brand: Hilti Pages: 31

Brand: Badger Meter Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands