Keysight Technologies S9106AC-2IF Startup Manual Download Page 53

Page: 53 / 80

4 Install Hardware

S9106AC-2IF, -4UP, and -42D 5G FR1 Multi-port Transceiver Solutions, Startup Guide

Item

Qty

Connection To... From...

RF loop-back cable with adapters (not included w/ S9106AC-42D)

Used during verification only; connect RF loop-back cable and adapters from
RF Out

➀

to RF In

➁

on Transceiver 1 and then on 2, 3, and 4. This same loop-

back cable with adapters can be moved to verify the High IF ports on Transceiver 1
and 2 as well as the HD ports; see

Verify Operation

on page

RF loop-back cable with adapters (or equivalent) can be used:
5063-1530 RF Cable, SMA (m) to SMA (m), 152.4 mm (6.0 in)
with two 1250-1250 Adapters, SMA (f) to Type-N (m)

4. 4. 1 Connect Cables, LAN Cables, a Display, a Keyboard & Mouse

1. Connect cables as shown in the equipment setup above.

2. Connect LAN 1 (top) to the Site LAN at your facility.

3. Connect LAN 2 (bottom) to the E7770A CIU CONTROL

➅

(rear panel).

4. Connect a Display, Keyboard & Mouse (Not included with S9106AC-42D).

Summary of Contents for S9106AC-2IF

















































































Search results

Summary of Contents for S9106AC-2IF

Reviews:

Related manuals for S9106AC-2IF

Brands by name

Popular brands

Keysight Technologies S9106AC-2IF, Startup Manual

Search results

Summary of Contents for S9106AC-2IF

Reviews:

Related manuals for S9106AC-2IF

Brands by name

Popular brands