manualshive.com logo in svg

Keysight Technologies N5221A, Service Manual, Page: 89 / 368

Share
Download
Keysight Technologies N5221A Service Manual Download Page 89

Keysight N5221A/22A Service Guide                                                                                            4-15

Troubleshooting
Power Up Troubleshooting

2.

If the display is dark (not visible), connect an external VGA monitor to the 

rear panel Monitor output connector. (Be aware that some multisync 

monitors might not be able to lock to a 60 Hz sync pulse.) If the video 

information is not present on the external VGA monitor, the most probable 

cause is the A17 CPU board. Refer to 

“Removing and Replacing the A17 

CPU Board Assembly” on page 7-25

.

3.

If the external VGA monitor displays the correct information, verify that 

the front panel interface ribbon cable is properly plugged into the 

motherboard connector. Refer to 

“Removing and Replacing the Front 

Panel Assembly” on page 7-8

.

4.

If the front panel interface ribbon cable is properly connected, suspect 

that one or more of the following is defective: 

—

inverter board (mounted on the display assembly)

—

A1 front panel interface board

—

A3 display assembly

Summary of Contents for N5221A

















































































































































































































































































































































































Reviews:

No comments