manualshive.com logo in svg

Keysight Technologies N5221A, Service Manual, Page: 105 / 368

Share
Download
Keysight Technologies N5221A Service Manual Download Page 105

Keysight N5221A/22A Service Guide                                                                                            4-31

Troubleshooting
Measurement System Troubleshooting

Figure 4-8 

Typical 8-Receiver Display for 4-Port Models

— If all traces are present and are similar to the traces in 

Figure 4-7

 or 

Figure 

4-8

, then there are no major problems with the analyzer’s measurement 

system. There may, however, be a minor failure in the analyzer.
To test further:

— Go  to 

Chapter 3, “Tests and Adjustments.”

 and perform all the tests 

in that section. 

— If a problem still exists, contact Keysight. Refer to 

“Contacting 

Keysight” on page 2-7

.

— If any of the traces are not present, are noisy or distorted, or are at an 

incorrect level, then there is a problem with the analyzer’s measurement 

system. Proceed to 

“Where to Begin Troubleshooting.”

Where to Begin Troubleshooting

For the purposes of troubleshooting, the analyzer block diagram is divided into 

the following functional groups:

— the source and LO group

Summary of Contents for N5221A

















































































































































































































































































































































































Reviews:

No comments