manualshive.com logo in svg

Keysight Technologies N5221A, Service Manual, Page: 333 / 368

Share
Download
Keysight Technologies N5221A Service Manual Download Page 333

Keysight N5221A/22A Service Guide                                                                                            8-5

General Purpose Maintenance Procedures
Error Terms

Figure 8-3 

Flowgraph of Three-Port Error Terms

where:

E = error term

DIR = Directivity

MAT = Forward Source Match and Reverse Load Match

TRK = Forward Reflection Tracking and Reverse Transmission Tracking

For the case of a full 3-port calibration, port 1 has

three Match error terms:

S11 source match

S12 load match

S13 load match

and three Tracking error terms:

S11 reflection tracking

S12 transmission tracking

S13 transmission tracking

There are six isolation terms not shown.

Summary of Contents for N5221A

















































































































































































































































































































































































Reviews:

No comments