manualshive.com logo in svg

Keysight Technologies N5221A, Service Manual, Page: 276 / 368

Share
Download
Keysight Technologies N5221A Service Manual Download Page 276

 7-12                                                                                           Keysight N5221A/22A Service Guide

Repair and Replacement Procedures
Removing and Replacing the A1–A3 and Other Front Panel Subassemblies

7-

Removing the A3 Display Assembly and the Touchscreen

1.

Disconnect the following cables from the A1 front panel interface board: 
display cable (item 

①

), inverter board cable (item 

➁

), touchscreen 

controller board cable (item 

③

), and power switch cable (item 

④

).

2.

Remove six screws (item 

⑤

) from the A3 display assembly and remove the 

A3 display assembly from the front panel assembly.

3.

The touch screen can now be removed from the front panel assembly. 

Note the orientation of the touch screen in the front panel assembly for 

installation of the new touch screen.
To replace the touch screen, note the orientation of the rubber boot on the 

old touch screen and then remove it and install it on the new one in the 

same orientation.

Summary of Contents for N5221A

















































































































































































































































































































































































Reviews:

No comments