Keysight Technologies N5221A Service Manual Download Page 310

Page: 310 / 368

7-46 Keysight N5221A/22A Service Guide

Repair and Replacement Procedures
Removing and Replacing the A34–A37 Source Attenuators, the A38–A41 Bias Tees,

and the A42–A45 Receiver Attenuators

11.

Remove two screws (item

⑤

) to remove the attenuator or bias tee to be

replaced, from the mounting bracket.

Replacement Procedure

Reverse the order of the removal procedure.
Torque all cable connections to 10 in-lbs.

Perform the post-repair adjustments, verifications, and performance tests

that pertain to this removal procedure. Refer to

Table 7-2 on page 7-60

Summary of Contents for N5221A

















































































































































































































































































































































































Search results

Summary of Contents for N5221A

Reviews:

Keysight Technologies N5221A, Service Manual, Page: 310 / 368

Search results

Summary of Contents for N5221A

Reviews: