manualshive.com logo in svg

Keysight Technologies N5221A, Service Manual, Page: 313 / 368

Share
Download
Keysight Technologies N5221A Service Manual Download Page 313

Keysight N5221A/22A Service Guide                                                                                            7-49

Repair and Replacement Procedures
Removing and Replacing the A38–A41 Bias Tees

2.

As shown in 

Figure 7-22

, position the bias tees on the attenuator brackets 

so that the port 1 and port 3 bias tees capacitors face each other. The port 

2 and port 4 bias tee capacitors should also face each other.

3.

Perform the post-repair adjustments, verifications, and performance tests 

that pertain to this removal procedure. Refer to 

Table 7-2 on page 7-60

.

Figure 7-21 

A38 through A41 Bias Tees Removal

Figure 7-22 

Orientation of Bias Tee Capacitors

Summary of Contents for N5221A

















































































































































































































































































































































































Reviews:

No comments