KETRON SD5, Owner'S Manual

Page: 78 / 122

using the Modulation or some other MIDI parameter that direc-
tly affects the voice. The MIDI filters can also be used to better
control an external MIDI module. The page called up from F5
FFiilltteerr shows a table of four rows and four columns relative to
the sixteen Parts. To be able to access the MIDI filter of a single
Part use the FF11 and FF66 push buttons for Parts 1, 2, 3 and 4 that
are to be selected by pressing the same push buttons repea-
tedly. Use push buttons FF22 and FF77 for Parts 5, 6, 7, and 8.
Use push buttons FF33 and FF88 for Parts 9, 10, 11 and 12 and push
buttons FF44 and FF99 for Parts 13, 14, 15 and 16. Once the Part to
which the MIDI filter is to be applied has been found, select
which MIDI message is to be cut-out from the reproduction
using the D
DA ATTA A C CU UR RSSO OR R push buttons and enable the filter
using the FF110 0 O Onn//O Offff push button. The filter is enabled when “O ON N” appears next the MIDI message to be filtered. The MIDI mes-
sages that can be filtered are the following:
Notes: all notes within the track
C Coonnttrrooll C Chhaannggee: all Control Changes within the track
PPrrooggrraam m C Chhaannggee:: all Program Changes
A Afftteerr TToouucchh:: all After touch events
PPiittcchh B
Beenndd:: all Pitch Bend events
V Voolluum mee:: only Control Change 07 Volume
PPaann:: only Control Change 10 Pan
R
Reevveerrbb:: only Control Change Reverb Send
C
Chhoorruuss:: only Control Change Effect Send
M
Moodduullaattiioonn W Whheeeell:: only Control Change 01 Modulation
EExxpprreessssiioonn:: only Control Change 11 Expression
R
RPPN N:: only Control Change RPN
N NR RPPN N:: only Control Change NRPN
To exit from FF55 FFiilltteerr press EEXXIITT or FF55 EEssccaappee that send to the main page of SSoonngg PPllaayy.
F6 Key Shift: This changes the transposition of the track selected by up to +/- 24 semitones. The value can be changed using the D DA ATTA A
C CU UR RSSO OR R push buttons which, if pressed together at the same time, reset the value.
F7 Channel Tx Rx : When push button FF77 is pressed repeatedly, it switches from TTXX (that indicates the transmission MIDI channel of the selec-
ted part) to R
RXX (that establishes the MIDI receiving channel). The value can be changed using the D DA ATTA A C CU UR RSSO OR R push but-
tons. If no value is specified the track receives and transmits on the MIDI channel having the same number as the Part.
F8 Part Mode : This modifies the operational mode of the track, using the D DA ATTA A push buttons. The possible choices are:
Voice: track dedicated to the use of a voice
D Drruum msseett:: track dedicated to the use of a Drumset
D Drruum m22:: track dedicated to the use of Live Drumsets
V Vooccaalliizzee:: track dedicated to the control of the Vocalizer
Based on the choice made, Drumset, Live Drum, Voice and Vocal Set can be called up or otherwise. Whereas in the case of
Voice and Drumset mode the Voice and Drumset are called up normally. For Drum 2 and Vocal Set the Live Drums and Vocal
Sets must be selected using the V
VA ALLU UEE ++//-- push buttons. The modification of operational mode of a track can make the song
incompatible with modules in General MIDI.
F9 Mute : If the function is enabled, the track is cut-out from the reproduction.
F10 16 Parts : This enables the display of each single parameter, showing its value for all sixteen Parts.
MODIFYING A PARAMETER FOR THE SIXTEEN GM PARTS
As already mentioned, the status of a single parameter for all sixteen tracks can
be displayed using the FF110
0 1166 PPaarrttss function. To rapidly access a parameter, select
it from the G GM M PPaarrtt page and then press FF110 0 1166 PPaarrttss to display the status of that
parameter for the sixteen tracks. The page FF110
0 1166 PPaarrttss structure shows a table
with four lines and four columns relative to the sixteen Parts. To access the single
Part use push buttons FF11 and FF66 for Parts 1, 2, 3 and 4 that are selected by pres-
sing the same push buttons repeatedly. Use push buttons FF22 and FF77 for Parts 5, 6,
7, and 8. Use push buttons FF33 and FF88 for Parts 9, 10, 11 and 12 and push buttons FF44
and FF99 for Parts 13, 14, 15 and 16. Once the Part has been found its value can be
modified using the D
DA ATTA A C CU UR RSSO OR R push buttons which, if pressed together at the
same time, will reset the value.
The parameters that can be modified in this way are distributed over seven pages
SD5
76
MIDI