NX-200
67
ADJUSTMENT /
调整
Controls
1
2 ABC
5 JKL
0
8 TUV
4
7
GHI
PQR
S
3 DE
F
6 MN
O
MIC
#
9 WXY
Z
PTT switch /
PTT开关
Universal connector
通用连接器
Power switch / Volume
电源开关/音量
Side1 key /
Side1键
Side2 key /
Side2键
Orange key
橙色键
Selector
选择器
Panel Test Mode
■
Test mode operation features
This transceiver has a test mode.
To enter test mode,
press and hold the [ ] key while turning the transceiver
power ON. Before the transceiver enters test mode, the
frequency version information appears on the LCD mo-
mentarily.
Test mode can be inhibited by programming. To
exit test mode, turn the transceiver power OFF. The follow-
ing functions are available in test mode.
■
Key operation
Key
“FNC” not appears on the sub LCD display
Function
Display
[Selector]
-
-
[
]
Push: Test channel up
Hold: Test channel up
continuously
Channel No.
[
]
Push: Test channel down
Hold: Test channel down
continuously
Channel No.
[Side1]
Push: Squelch level up
Hold: Squelch off
Squelch level
Squelch off: icon appears
[Side2]
Wide/Narrow/Very narrow
Wide: “w”
Narrow: “n”
Very narrow: “v”
[ ]
Shift to panel tuning mode -
[ ]
Function on
“
FNC
” appears on the
sub LCD display
[ ]
MSK 1200bps and 2400bps 2400bps: icon appears
[
]
Push: Test signaling up
Hold: Test signaling up
continuously
Signaling No.
[Orange]
-
-
[PTT]
Transmit
-
[0] to [9]
and
[#], [ ]
Use as the DTMF keypad.
If a key is pressed during
transmission, the DTMF
corresponding to the key
that was presses is sent.
-
控制器
面板测试模式
■测试模式操作功能
本手持对讲机有测试模式。
要进入测试模式，打开手持对
讲机电源时，按住 [
] 键。手持对讲机进入测试模式之前，
LCD 上短时间出现频率版本信息。
可以通过编程禁用测试模
式。如需退出测试模式，请关闭手持对讲机电源。在测试模
式可以使用下列功能。
■键操作
键
副 LCD 显示上不出现“FNC”
功 能
显 示
[ 选择器 ] -
-
[
]
按下 : 测试信道递增
按住 : 测试信道持续递增
信道号
[
]
按下 : 测试信道递减
按住 : 测试信道持续递减
信道号
[Side1]
按下 : 静噪电平递增
按住 : 静噪关
静噪电平
静噪关。
图标出现
[Side2]
宽 / 窄 / 超窄
宽 :“w”
窄 :“n”
超窄 :“v”
[ ]
换到面板调谐模式
-
[
]
功能开
副 LCD 显示上出现“FNC”
[
]
MSK 1200bps 和 2400bps
2400bps:
图标出现
[
]
按下 : 测试信令递增
按住 : 测试信令持续递增
信令号
[ 橙色 ]
-
-
[PTT]
发射
-
[0] 至
[9] 和
[#]，[ ]
用作 DTMF 键盘。如果在
发射时按下某个键，则
发送与按下的键对应的
DTMF。
-
