Keba ServoA SA52.0100 Operation Manual Download Page 57

Page: 57 / 70

ServoA

Operation Manual

Diagnostics

ID no.: LDS-O-SA-EN-202103

Display

Software code

Error

number

Error description

E-ENC

170

HIPERFACE: unspecific error

171

HIPERFACE: the asynchronous interface reports a sys-
tem error (T8R=0). No byte was received from encoder
Please contact your service provider

172

HIPERFACE: the asynchronous interface reports a time
out error

176

HIPERFACE: time out error

177

HIPERFACE: CRC error in status response

178

HIPERFACE: CRC error in command response

179

HIPERFACE: mismatch in command response

180

HIPERFACE: error in error status response, see status
response in HFST[5] for details

181

HIPERFACE: error bit was set, see status response in
HFST[5] for details

182

HIPERFACE: status response, see status response in
HFST[5] for details

185

The number of sine-cosine lines is not correct

191

Electronic name plate (ENP): no OEM memory defined in
the encoder,
function “Electronic Nameplate” not available

192

ENP: Interface error
Please contact your service provider

193

ENP: OEM data error, block number not found,
function “Electronic Nameplate” not available

194

ENP: OEM data error, data CRC check failed
function “Electronic Nameplate” not available

195

ENP: FrameCheck error, error in frame check
function “Electronic Nameplate” not available

196

ENP: Write parameter error, error during parameter
access
Please contact your service provider

Display

Software code

Error

number

Error description

E-ENC

202

ENP: error in process block 2 “ECOFF”
Please contact your service provider

203

ENP: error in process block 3 “MotDatSM”
Please contact your service provider

204

ENP: error in process block 4 “MotDatSafety”
Please contact your service provider

205

ENP: error in process block 5 “MotDatComp”
Please contact your service provider

206

ENP: error in process block 6 “MotDatASM”
Please contact your service provider

207

ENP: error in process block 7 “MotDatLin”
Please contact your service provider

E-FLW

Tracking error

140

Speed tracking error, reduce load or acceleration, activa-
te speed ramps or increase allowed speed tracking error

153

Speed to high, check position sensor, reduce torque in
generator mode,
check parameters MOSNM and SCSMX

240

Position tracking error, reduce load or acceleration,
increase allowed position tracking error

E-SWL

Software limit switch alarm

243

Positive software limit switch activated, check moving
area between positive and negative software limit
switches

244

Negative software limit switch activated, check moving
area between positive and negative software limit
switches

246

New reference value outside the range of software limit
switches

Summary of Contents for ServoA SA52.0100







































































Search results

Summary of Contents for ServoA SA52.0100

Reviews:

Related manuals for ServoA SA52.0100

Brands by name

Popular brands

Keba ServoA SA52.0100, Operation Manual

Search results

Summary of Contents for ServoA SA52.0100

Reviews:

Related manuals for ServoA SA52.0100

Brands by name

Popular brands