Keba ServoA SA52.0100 Operation Manual Download Page 37 | Manualshive

Page: 37 / 70

background image

37

ServoA

Operation Manual

Electrical installation

ID no.: LDS-O-SA-EN-202103

ATTENTION!

The external braking resistor must be monitored by the control.

The temperature of the braking resistor is monitored by a temperature
watchdog (Klixon). In the event of overheating the drive controller must be
disconnected from the mains supply.

Please consult your projecting engineer for more detailed information on the design of
braking resistors.

!

3.12.3 Connection of an external braking resistor

ATTENTION!

• Be sure to follow the installation instructions for the external braking resis

-

tor.

• The temperature sensor (bimetal switch) on the braking resistor must be

wired in such a way that the power stage is deactivated and the connected
drive controller is disconnected from the mains supply if the braking resistor
overheats.

• The minimum permissible connection resistance of the drive controller

must not be infringed, for technical data see chapter A.1.

• The braking resistor must be connected by a shielded cable.

Size BG2 ~ BG4

Size BG5

Figure 3.15.1 Connection of braking resis-

tor for ServoA BG2-BG4

Figure 3.15.2 Connection of braking resis-

tor for ServoA BG5

ATTENTION!

No additional external braking resistor must be connected to

the drive controller with integrated braking resistor.

DANGER FROM ELECTRICAL TENSION!

Danger to life! Never wire or

disconnect electrical connections while they are live. Always disconnect the
power before working on the device. Dangerously high voltages of ≥ 50 V
may still be present 10 minutes after the power is cut (capacitor charging).
So check that the power has been cut!

!

!

«
...
35
36
37
38
39
...
»

Summary of Contents for ServoA SA52.0100







































































Reviews:

No comments

Related manuals for ServoA SA52.0100

Brand: T-Verter Pages: 121

Brand: Happy Pages: 10

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 168

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 29

Brand: Panasonic Pages: 37

Brand: Panasonic Pages: 9

Brand: Eaton Pages: 6

Brand: Danfoss Pages: 37

Brand: Daikin Pages: 44

Brand: Harman Pages: 2

Brand: T-Link Pages: 3

Brand: Watts Pages: 4

Brand: ZIMMERLI MESSTECHNIK Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands