Kärcher SB-Wash-E 10, Manual

Page: 34 / 44

-
13
Other interruptions can only be removed by
the Service.
order number: 6.414-278
order number: 6.393-474
Without content.
order number: 6.393-480
Without content.
Lid for the cleaning agent container 10 liter,
order number: 6.393-045
Best.-Nr.: 6.288-218
Order no. : 6.288-072.0
Order no. : 6.288-116.0
Best.-Nr.: 6.288-001.0
Order no. : 6.290-911.0
order number: 6.287-016
25 kg, for option base exchanger
For the optional softener:
몇
Warning!
Before using the cleaning agent, please re-
fer to the notice on the package. Do not use
the following cleaning agents:
–
cleaning agent containing nitrit acid
–
cleaning agent containing active chlo-
rinate
If you use such cleaning agents, it will dam-
age your equipment.
The cleaning agents are to be used undilut-
ed.
RM 100 ASF
RM 101 ASF
The warranty terms published by our com-
petent sales company are applicable in
each country. We will repair potential fail-
ures of your accessory within the warranty
period free of charge, provided that such
failure is caused by faulty material or de-
fects in fabrication. In the event of a warran-
ty claim please contact your dealer or the
nearest authorized Customer Service cent-
er. Please submit the proof of purchase.
–
Only use accessories and spare parts
which have been approved by the man-
ufacturer. The exclusive use of original
accessories and original spare parts
ensures that the appliance can be oper-
ated safely and trouble free.
–
For additional information about spare
parts, please go to the Service section
at www.kaercher.com.
Caution
Risk of injury and damage! Observe the
weight of the appliance when you transport
it.
Caution
Risk of injury and damage! Note the weight
of the appliance in case of storage.
Notice
The equipment may only be installed by an
–
mechanic of Kärcher
–
or an from Kärcher authorized individu-
al
The following requirements are necessary
in order to install the equipment:
–
Straigh even area, with a solid subsoil
with the measures of 1040x725 mm.
–
For the option of the base exchanger/
Osmose an additional area of 845 x 725
mm.
–
Using the option of the base exchanger/
Osmose: Water connection with pipe
separator according to DIN 1717, per-
forming data, refer to " technical data".
Please pay attention to the national re-
quirements (in Germany DVGW).
–
Power connection, refer to "technical
data".
–
By customer, lockable, access for the
wash customer emergency - off- main
switch.
–
Light at the washing area according to
the national requirements, in order to
assure safe working for the customer
when dark.
–
Power and water supply according to
the measuring sheet.
–
By operation in the winter, an isolated/
heated water supply sytem must be
guaranteed.
–
Drain water shaft and required drain
water disposal.
–
Drill fixing holes according to the meas-
ure sheet.
Unpack the equpiment and dispose of the
packing material properly.
Interruptions at the base exchanger (optional)
Interruption Possible cause Repair By whom
base exchanger
does not regen-
erate No power supply Check power supply (fuse, switch, jack). Operator,
Maintenance
Switch clock at the head of the base ex-
changer is wrong adjusted or, after an in-
terruption of the power supply was not
adjusted. Set the time at the switch clock. Operator
The water stays
hard after the re-
generartion No salt in the salt tank Fill in salt, let the level of the salt not get below the wa-
ter level. Operator
No sole suction water input pressure is too low Increase the water pressure to the minimum of 0,2
MPa (2 bar) . Operator
Accessories
Attachment sets
Water filter G 1“
container
Cleaning agent container 25 liter
Cleaning agent container 10 liter
Fuel
Motor oil 0-W40
Silicon grease
Lock grease
Moisture protection spray
Steel care product
Water softening salt in form of tabletts
Softener RM 110
Detergent
Dosing ml/
min
CHEM 1 RM 806 ASF 25
CHEM 2 RM 820 ASF 15
Lime solvent
Warranty
Spare parts
Transport
Storage
Installing the unit
(only for experts)
Preparing the installation place
Unpack the equipment
34 EN