-
7
Adjust sweeping track:
Adjust the left and right adjustment le-
vers and engage into the same boring.
– Engage adjustment lever into the lower
boring (+): Sweeping track becomes
bigger
– Engage the adjustment lever into the
upper boring (-): Sweeping track be-
comes smaller
Check sweeping mirror.
Replacement is due if a visible deteriora-
tion in sweeping performance caused by
bristle wear is evident.
Note:
The appliance may only be tilted
backwards if the fuel tank is empty.
Note:
Close the fuel tap, remove the waste
container and move the pushing handle to
the front prior to tilting the appliance. Do not
rest the appliance on the pushing handle.
Unscrew 3 screws from the underside
of the side brush.
Remove the wiper blade.
Clip new side brushes on to driver and
screw on.
Adjustment is necessary if a visible deterio-
ration in sweeping performance caused by
side-brush is evident.
Release the wing nut.
Adjust the adjustment screw.
Tighten the wing nut.
– Adjustment is necessary if the bulk
waste flap cannot be raised wide
enough.
– The Bowden cable needs to be re-
leased a little if the sweeper results be-
come poorer, for e.g. due to the wearing
of the front lip.
Loosen counter-nut.
Adjust the adjustment screw.
Tighten the counter-nut.
Note:
The appliance may only be tilted
backwards if the fuel tank is empty.
Note:
Close the fuel tap, remove the waste
container and move the pushing handle to
the front prior to tilting the appliance. Do not
rest the appliance on the pushing handle.
Front sealing strip
Loosen the fastening screws of the
sealing strip.
Adjust or replace sealing strip.
Set the distance between the sealing
strip and the floor so that the bottom
edge trails behind at a distance of be-
tween 0-10 mm.
Adjust sealing strip.
Tighten the fastening of the sealing
strip.
Rear sealing strip
Remove the waste container.
Loosen the fastening screws of the
sealing strip.
Adjust or replace sealing strip.
Set the distance between the sealing
strip and the floor so that the bottom
edge trails behind at a distance of be-
tween 0-10 mm.
Tighten the fastening of the sealing
strip.
Side sealing strips
Loosen the fastening screws of the
sealing strip.
Adjust or replace sealing strip.
To set the floor clearance, insert a
sheet with a thickness of max. 2 mm un-
der the sealing strip.
Adjust sealing strip.
Tighten the fastening of the sealing
strip.
몇
Warning
Empty waste container before replacing
dust filter. Wear a dust mask when working
around the dust filter. Observe safety regu-
lations on the handling of fine particulate
material.
Lock parking brake.
Shake off dust filter.
Open the locking screw of the dust filter
cover in an anticlockwise direction.
Lift the dust filter cover.
Replace dust filter Make sure the dust
filter is inserted correctly (see figure).
Screw in the locking screw all the way.
Caution
If the locking screw is not tightened all the
way, there may be damages.
Note:
Make sure when installing the new
filter that the fins are not damaged.
Setting range
(-) 1...10 (+)
Minimum sweeping track
1
Maximum sweeping track
10
New roller brush
1...3
Replacing side brush
Adjust side-brush lowering
Adjust the raising of the bulk waste flap
Adjusting and replacing sealing strips
Replacing dust filter
Accessories
Hard side-brushes
6.905-625.0
For removing stubborn dirt in the external
area; resistant to moisture.
Roller-brush, soft
6.906-886.0
With natural bristles especially for fine
dust sweeping on smooth indoor floors.
Not resistant to wetness; not for abrasive
surfaces.
Roller-brush, hard
6.906-885.0
For removing stubborn dirt in the external
area; resistant to moisture.
Roller brush, anti-
static
6.906-950.0
18
EN
Summary of Contents for 1.049-200
