Kaba Peaks Classic Technical Manual Download Page 48

Page: 48 / 92

Section 3 - 4

Peaks products may be pinned to the A2 or A4 system. The patent pin stack is built into the face of all small

format interchangeable cores. In large format interchangeable cores and conventional cylinders, the patent pins

are installed when combinating. Certain products have a large diameter plug and require longer bottom pins. All

products use the same top pins.

Peaks Preferred Patent pins

Spring

3425-00-3002

patent top pin

(for conventionals & KIK)
8800-00-3004

patent bottom pin for all

products except those with

large diameter plugs

8144-00-3004

patent bottom pin for the Universal 8400-xx-1099, the

8400-xx-1095 key-In-knob, the 8144 Corbin Russwin,

the 8544 Sargent and the 8444 Schlage large format

interchangeable cores.

3800-00-4010
stainless steel for all Peaks products

except 8444

6440-00-4010

3800-00-3005

patent top pin

(all cores other than conventional & KIK)

2JS

3JS

4JS

7AS

8AS

9AS

J series bottom pins are for the large diameter plugs

only

0J thru 4JS are the same as 5A thru 9AS, respectively.

Tumbler pins

Peaks pins are crowned for smooth operation and long cylinder life. Bottom pins are nickel silver. Spool pins are

used to increase pick and impression resistance. Bottom pins are .003" shorter than after market replacement

pins.

Non-original pins will not work properly in Kaba products and their use voids product warranty.

A2 system:

Use A series bottom pins for everything except the 8400-xx-1095 and 3400-xx-1095 key-in-knob, the

Universal 8400-xx-1099 and 3400-xx-1099 key-in-knob cylinder, the 8144/6140 Corbin Russwin, and 8544/6540

Sargent large format interchangeable core with large diameter plugs. J series bottom pins are required for prod-

ucts with large diameter plugs. Use B series master/top pins for all products.

A4 system:

Use E series bottom pins for everything except the 8400-xx-1095 and 3400-xx-1095 key-in-knob, the

Universal 8400-xx-1099 and 3400-xx-1099 key-in-knob cylinder and the 8144/6140 Corbin Russwin large format

interchangeable core with large diameter plugs. K series bottom pins are required for products with large diameter

plugs. Use F series master/top pins for all products.

1KS

2KS

4ES

5ES

K series bottom pins are for the large diameter plug

only

1K and 2K are the same as 4ES and 5ES, respectively.

Components for Pinning

Peaks Classic Patent pins

Spring

3425-00-3002

patent top pin

(for conventionals & KIK)

3800-00-3004

patent bottom pin for all

products except those with

large diameter plugs

6140-00-3004

patent bottom pin for the Universal 3400-xx-1099, the

3400-xx-1095 key-In-knob, the 6140 Corbin Russwin,

the 6540 Sargent and the 6440 Schlage large format

interchangeable core

3800-00-4010
stainless steel for all Peaks products

except 6440

6440-00-4010

3800-00-3005

patent top pin

(all cores other than conventionals & KIK)

Summary of Contents for Peaks Classic





























































































Search results

Summary of Contents for Peaks Classic

Reviews:

Related manuals for Peaks Classic

Brands by name

Popular brands

Kaba Peaks Classic, Technical Manual

Search results

Summary of Contents for Peaks Classic

Reviews:

Related manuals for Peaks Classic

Brands by name

Popular brands