Kaba Peaks Classic Technical Manual Download Page 6

Page: 6 / 92

Section 1 - 2

Peaks Preferred is the most cost effective, application flexible, patented end-user key control system

available

. Two projections near the key bow, called “peaks” are part of the utility patents safeguarding the

key blanks. The “peak” operates the patent pin stack. Since the uncut key blank itself is patented, Kaba con-

trols blank manufacture and distribution.

All Peaks key blanks are marked with a unique identification number. The Kaba key

control contract and this manual specify certain key control procedures. Breach of

contract or failure to abide by factory key records policies can result in loss of the

product line.

Contracts specify that:

1. The blank ID number may not be removed, stamped-over,

or altered in any way;

2. Parties under contract may not duplicate any keys bearing

a blank ID number different from their own;

3. Key blanks may not be sold, lent, or given away;
4. Proper key records must be kept and authorization procedures observed.

What is Peaks Preferred?

Key Blank Identification Number and Peaks Contracts

Summary of Contents for Peaks Classic





























































































Search results

Summary of Contents for Peaks Classic

Reviews:

Related manuals for Peaks Classic

Brands by name

Popular brands

Kaba Peaks Classic, Technical Manual

Search results

Summary of Contents for Peaks Classic

Reviews:

Related manuals for Peaks Classic

Brands by name

Popular brands