Kaba Peaks Classic Technical Manual Download Page 45

Page: 45 / 92

PAT # 7181941

Section 3 - 1

tti

&
P

Cylinder Stamping, Marking, Lubrication & Tailpiece Installation

Stamping and Marking

Kaba Access Control recommends marking cylinders with an indelible marker. If stamping or engraving of

cast cylinders is unavoidable the stamped or engraved area must be coated with a clear acrylic enamel

(Krylon, fingernail polish, etc.). Application by brush is preferable, but spray is acceptable as long as care is

taken to reduce overspray. Key-in-knob cylinders should never be stamped. Cores should be stamped on

the top half of the shell. Mortise and rim cylinders should be stamped on the back of the shell.

Lubrication

Kaba recommends the use of Poxylube

(a dry spray) for all Peaks Preferred cylinders.

Tailpiece Installation

Interchangeable Core

Stamp here

Rim cylinder

Stamp here

Mortise cylinder

Tailpiece inserted correctly, allowing

tip of key full insertion.

Tailpiece inserted

upside down,

preventing full key

insertion.

When inserting tailpiece horizontally it can be

flipped either way for proper operation.

Do not stamp

anywhere

Key-in-Knob

cylinder

Correct

Incorrect

Stamp here

Summary of Contents for Peaks Classic





























































































Search results

Summary of Contents for Peaks Classic

Reviews:

Related manuals for Peaks Classic

Brands by name

Popular brands

Kaba Peaks Classic, Technical Manual

Search results

Summary of Contents for Peaks Classic

Reviews:

Related manuals for Peaks Classic

Brands by name

Popular brands