Kaba Peaks Classic Technical Manual Download Page 77

Page: 77 / 92

Section 4 - 9

&
R

The standards given below are used by the factory in designing and generating bitting lists. They apply to

the top master key (TMK) in a system as well as the control key (CTR).

Design Standards

1. TMK’s should have at least one of the shallowest possible bittings in one progressed position, and one

of the deepest possible bittings in another position, whether it is progressed or not.
The purpose is to keep lower level keys from being cut down to the TMK or CTR bitting. The deepest

possible cut statistically reduces key manipulation (key picking) as does a moderately deep constant.

2. Moderate cut-to-cut variations should be employed. Extremes in adjacent cut depths cause

premature wear in the cylinder and on the key. Bittings of this type should be assigned last.

3. Uniformly shallow or deep keys should not be used. For example, 988789, is easy to pick, and any key

in the system can be cut down to it. Uniformly shallow keys, like 120112, also make the locks easy to

pick.

4. Declining step keys should be avoided. 976642 is an example of a declining step key. Such

keys, when worn, tend to pull out of a turned plug and make the cylinder less pick-resistant.

5. Deep cuts next to the bow should be avoided as they can weaken a key. Kaba recommends that this

position be progressed last in any key system to make all keys as strong as possible.

Control Keys (CTR)

The control key (CTR) should have the same characteristics as a top master key. The control key should

normally differ from the top master key in all positions. The control key cuts are chosen from the progression

columns of the KBA. The control is actually a change key. Note in the sample system that the key bitting

array has been manipulated so that the control key is the last key in the system.

When you cross the control key combination off the progression list, you can be certain that no other key in

the system will ever be a control key.

CTR 9 6 0 4 7 8

TMK 5 2 8 6 1 4

7 4 2 8 3 6

3 0 4 0 5 2

1 8 6 2 9 0

9 6 0 4 7 8

SOP a b c d e f

All systems should have different TMK’s and distinct CTR combinations.

TMK and control combinations

should be recorded in a register to prevent repetition of the combinations. Kaba recommends that parity

patterns be used to separate the master key systems from the KA and KD combinations for non-master

keyed projects.

CTR

9 6 0 4 7 8

deepest

shallowest

TMK

5 2 8 6 1 4

Designing Top Master Keys and Control Keys

Summary of Contents for Peaks Classic





























































































Search results

Summary of Contents for Peaks Classic

Reviews:

Related manuals for Peaks Classic

Brands by name

Popular brands

Kaba Peaks Classic, Technical Manual

Search results

Summary of Contents for Peaks Classic

Reviews:

Related manuals for Peaks Classic

Brands by name

Popular brands