Home
/
Kaba
/
ILCO FDU
/
User Manual

Kaba ILCO FDU, User Manual, Page: 172 / 276

Share

Page: 172 / 276

Kaba ILCO FDU User Manual Download Page 172

Locks – Using and Programming

Kaba Ilco Lodging Access Control System

161

3.

Press 1 or < > to reach the “Lock Programming” menu.

4.

Press 7 or use the down <

T

> arrow followed by < > to reach the “Electronic

Override” menu.

5.

Press < > to communicate with the lock and perform the override.

5.7.3

Overriding a RAC Card Reader

RACs control electrical devices such as magnetic locks, motorized doors and elevators,
using relays. There is an ON/OFF override switch built into the RAC panel box. Each
individual device should have an appropriate override installed to meet safety codes. An
elevator, for example, should have a stop button.

5.8 The

FDU

Override

As an alternative to mechanical and electrical overrides, the FDU provides an easier way
to override the privacy of 760, 770, and 710-II lock models. When the lock is
programmed with the override privacy feature, any staff employee may unlock this lock.
This is known as the “Global Australian Privacy Override” as this is typically only for

«
...
170
171
172
173
174
...
»

Summary of Contents for ILCO FDU





















































































































































































































































































Reviews:

No comments