manualshive.com logo in svg

Kaba ILCO FDU, User Manual, Page: 164 / 276

Share
Download
Kaba ILCO FDU User Manual Download Page 164

Locks – Using and Programming 

Kaba Ilco Lodging Access Control System 

 

153

Steps to reset the lock addresses:

1.

Program the new lock with the room number only. Refer to Sections 5.3.2, 5.3.3 
or 5.3.4 and skip the steps for setting the Sub-Master addresses (Section, Floor, 
Group, Zone and Area). 

2.

Swipe a keycard or enter a PIN value having a Programming authorized user 
level. 

3.

Press 8 or use the down <

T

> arrow followed by < > to reach the 

“Programming FDU/Lock” menu. 

4.

Press 1 or < > to reach the “Lock Programming” menu. 

5.

Press 2 or use the down <

T

> arrow followed by < > to reach the “Reset 

Addresses” menu. 

6.

Insert the Programming keycard in the lock that is to be the source for the 
addresses (old lock or a neighbouring lock), and ensure the green indicator is lit. 
Connect the communication cable from the FDU to the source lock and press 
any key on the FDU to read the addresses and valid keycards. 

Summary of Contents for ILCO FDU





















































































































































































































































































Reviews:

No comments