manualshive.com logo in svg

Kaba ILCO FDU, User Manual, Page: 159 / 276

Share
Download
Kaba ILCO FDU User Manual Download Page 159

Chapter 5 

148

Kaba Ilco Lodging Access Control System

Follow the instructions in the correct column: 

6.

Select

Guest Common Area

option, and then press < 

T

>.

  Press the right <

X

>  arrow   

to display all Guest Common 
Areas. 

       

7.

More than one or all 8 Guest 
Common Area addresses may be 
assigned to a single lock. Select 
the Guest Common Area, from 1-
8 (e.g. 1,2,4), and then press 

 

< >.

6.

Using the left <

W

> or right <

X

>   

arrow, select the 

Staff Common 

Areas

 option and then press 

<

T

>.

              Press  the  right  <

X

> arrow 

 

 

 

to display all Staff Common 

 Areas. 

7.

More than one of all 16 Staff 
Common Area addresses may be 
assigned to a single lock. Select 
the  Staff Common Area, from 1-
16 (e.g. 1,4,7), and then press 
< >.

NOTE: 
Only one type of
Common Area (Guest 
or Staff) can be chosen 
per lock. 

Summary of Contents for ILCO FDU





















































































































































































































































































Reviews:

No comments