manualshive.com logo in svg

Kaba ILCO FDU, User Manual, Page: 129 / 276

Share
Download
Kaba ILCO FDU User Manual Download Page 129

Chapter 4 

118

Kaba Ilco Lodging Access Control System

B.5 General Manager Authorization (GMA) 

Purpose: 

Grants access to all functions of the FDU. 

Intended for the highest level of user, including the Chief of Security, the General 
Manager and the System Administrator. 

Authorization #s: 

181 to 200 

Minimum keycard: 

General Manager Authorization 

Shortcut: Swipe 

authorized keycard, press 6 and 2 

Expiry: None 

Notes:

It is extremely important to make two spare GMA keycards in case of accidental 
erasure of the GMA keycard in general use. The spare GMA keycards must have two 
different authorization numbers that are not used for any other GMA keycard in the 
facility. These spare keycards should be stored in a safe. If it is necessary to use one 
of the spare GMA keycards, immediately make another spare and lock it in the safe. 

B.6 POS Authorization

Purpose: 

Grants access to the functions of the Point-of-Sale Verifier mode of the FDU. There 
are no menus associated with the POS mode. Simply swipe the POS Authorization 
keycard to put the FDU in POS Verifier mode that can be used to verify a guest’s 
keycard in order to post charges to their room. 

Authorization #s: 

1 to 200 

Minimum keycard: 

Master Authorization 

Shortcut: Swipe 

authorized keycard, press 6 and 2 

Expiry: None 

Notes: 

The POS verifier must be enabled in the FDU features.  

POS Authorization keycards are completely separate from the other Authorization 
levels. A POS Authorization keycard can share the same Authorization number as an 
FDA, PA, MA, BA or GMA keycard without cancelling the other keycard, and vice-
versa. 

Summary of Contents for ILCO FDU





















































































































































































































































































Reviews:

No comments