Home
/
Kaba
/
ILCO FDU
/
User Manual

Kaba ILCO FDU, User Manual, Page: 160 / 276

Share

Page: 160 / 276

Kaba ILCO FDU User Manual Download Page 160

Locks – Using and Programming

Kaba Ilco Lodging Access Control System

149

8.

Press < > when ready to program the lock.

9.

Only for a lock, insert the Programming keycard in the lock, and ensure the
green indicator is lit. For a RAC, use the Initialization keycard instead of the
Programming keycard to initialize communication.

10. Connect the communication cable from the FDU to the lock and press any key

on the FDU to send the programming to the lock.

The addresses are now assigned. Every time lock addresses are programmed, the
FDU sets the lock’s internal clock to the correct time, so there is no need to reset
the lock time. Remove the communication cable from the lock.

5.3.6

Programming Restricted Area Locks

Purpose:

To program the address of a lock for a Restricted
Area. The only keycards accepted by Restricted Area
locks are the correctly addressed Restricted Area
keycard, and the Emergency keycard. Only one
address needs to be programmed into the lock, which
is the Restricted Area number (from 1 to 200).

Level Available

Addresses

Example

Restricted Area

1-200

169

Emergency Master

-

All

Table 5.3.6:

Addresses for a Restricted Area 169 lock.

«
...
158
159
160
161
162
...
»

Summary of Contents for ILCO FDU





















































































































































































































































































Reviews:

No comments