background image

15

PXI STAR Trigger

When PXI STAR is selected as the trigger source, the PXIe-69529 accepts a TTL-compatible 

digital signal as a trigger signal. The trigger occurs when a rising edge or falling edge is 

detected at PXI STAR, with trigger polarity configurable by software, with minimum pulse 

width requirement of the digital trigger signal 300 ns.

PXIe_DSTARB Trigger

The  PXIe_DSTARB  signal,  a  differential  signal  transmitted  via  the  PXI  Express  Chassis 

backplane,  distributes  high-speed,  high-quality  trigger  signals.  When  PXIe_DSTARB  is 

selected as the trigger source, the PXIe-69529 accepts a fast-switching LVDS digital signal 

as  a  trigger  signal.  Triggering  occurs  when  a  rising  edge  or  falling  edge  is  detected  at 

PXIe_DSTARB, with trigger polarity  configurable by software, with minimum pulse width 

requirement 300 ns. 

PXI Trigger Bus

The  PXIe-69529  utilizes  PXI  Trigger  Bus  Numbers  0  through  7  to  act  as  a  System 

Synchronization Interface (SSI). With the interconnected bus provided by PXI Trigger Bus, 

multiple modules are easily synced. When configured as input, the PXIe-69529 serves as a 

slave module and can accept trigger signals from one of buses 0 through 7. When configured 

as output, the PXIe-69529 serves as a master module and can output trigger signals to the 

PXI Trigger Bus Numbers 0 through 7. 

Analog Trigger

The  PXIe-69529  analog  trigger  circuitry  can  be  configured  to  monitor  one  analog  input 

channel from which data is acquired. Selection of an analog input channel as the analog 

trigger  channel  does  not  influence  the  input  channel  acquisition  operation.  The  analog 

trigger circuit generates an internal digital trigger signal based on the condition between 

the analog signal and the defined trigger level. 
Analog trigger conditions are as follows:

•  Positive-slope trigger: The trigger event occurs when the analog input signal changes 

from  a  voltage  lower  than  the  specified  trigger  level  to  a  voltage  exceeding  the 

specified trigger level.

•  Negative-slope  trigger:  The  trigger  event  occurs  when  the  analog  input  signal 

changes from a voltage exceeding the specified trigger level to a voltage lower than 

the specified trigger level.

Summary of Contents for PXIe-69529





























Reviews: