10
▋
▋
2.4GHz▋Antenna▋Considerations
2.4GHz band radio waves have strong directionality so receiving sensitivity differs greatly depending on the
direction of antenna orientation.
※ If the antenna is attached directly to a shielding material such as carbon or metal, the receiving sensitivity of the
antenna is considerably reduced.
Multi Coaxial Antenna type receiver (more than one coaxial antenna extending from the receiver)
Be sure to install the antenna’s at right angles to each other, rather than parallel.
Single Coaxial Antenna type receiver
Avoid placing the antenna along a carbon fuselage, or surrounded by metal materials.
▋
▋
Remote▋Antenna▋installation
The remote Antenna RA01L receives data from the transmitter, and also feeds telemetry data back to the
Transmitter so it is highly recommended to locate the Remote Antenna away from the main Receiver unit, ESC,
Regulator, Servos, Gyro Sensors, harness or Power cables, etc to avoid interference.
RX
RX
RX
RX
×
間違ったアンテナの設置方向
アンテナに対しての受信方向を表記
Receiving Sensitivity (High)
RX
RX
Receiving
Sensitivity
(Low)
Material Frame
Receiving
Sensitivity
(High)
Receiving Sensitivity (High)
※Take care not to
damage the anten-
nas projecting from
the aircraft body.
Aircraft body surface made
from shielding material.
Weak
Signal
Strong
Reception
Strong
Reception
The antenna part should be installed
in a perfectly straight condition.
RG Cable
RG631B
Remote Antenna
Strong
Reception
Strong
Reception
Weak
Signal
※The remote antenna
receives data
and also feeds back
to the transmitter
(telemetry).
▼ Front Face
▲ Rear Face
RA01T/C Side View
Built-in Antenna
Circuit Board Face
The built-in antenna of the remote antenna is
installed on the surface of the circuit board.
Care will be required in the situation where the
built-in antenna has been installed beside a
shielding material, since the receiving sensitiv-
ity will be considerably degraded.
Location of LED light
1. Are the transmitter and receiver batteries fully charged?
2. Is the remote antenna securely connected?
3. Is the distance between the transmitter and receiver too close?
4. When the procedure is carried out on the top of a desk or
bench top that is made from metal, the binding procedure
may not be successful.
If the bind process or range check is not successful,
check the following items:
Please note that when the model or model type is
changed in the transmitter, re-binding will be required.
Never fly the aircraft in Range Check mode.
Be sure that the failsafe settings are set in the
transmitter.
40 meters
各アンテナを互いに水平に設置すると、単一方
向の受信になるため、受信効率が低下します。
Bind plug
Binding terminal
Connecting
the battery to a
spare channel
RX battery
(sold separately)
Connection Chart
Switch harness
(sold separately)
Y-Harness
(sold separately)
RG631B Receiver
ORANGE
BROWN
RED
( )
( )
( )
ORANGE
BROWN
RED
( )
BROWN
( )
( )
RED
( )
( )
ORANGE
( )
Harness connection
Insert the connector,
taking adequate care
of the direction.
Sensor Installation
When connecting sensors, connect
a Y-Harness (sold separately) to the
(BIND/BATT/SENS) terminal.
Note that Sensors do not need
to be bound together with the
Transmitter and receiver.
C o a x i a l p a r t o f t h e
antenna can be bent
however, do not bend it
in a sharp angle. This
will damage the internal
antenna wires.
SENSOR
SENSOR
(sold separately)
Optional Remote Antenna RA01T/C
RX
RX
RX
RX
×
間違ったアンテナの設置方向
アンテナに対しての受信方向を表記
Receiving Sensitivity (High)
RX
RX
Receiving
Sensitivity
(Low)
Material Frame
Receiving
Sensitivity
(High)
Receiving Sensitivity (High)
※Take care not to
damage the anten-
nas projecting from
the aircraft body.
Aircraft body surface made
from shielding material.
Weak
Signal
Strong
Reception
Strong
Reception
The antenna part should be installed
in a perfectly straight condition.
RG Cable
RG631B
Remote Antenna
Strong
Reception
Strong
Reception
Weak
Signal
※The remote antenna
receives data
and also feeds back
to the transmitter
(telemetry).
▼ Front Face
▲ Rear Face
RA01T/C Side View
Built-in Antenna
Circuit Board Face
The built-in antenna of the remote antenna is
installed on the surface of the circuit board.
Care will be required in the situation where the
built-in antenna has been installed beside a
shielding material, since the receiving sensitiv-
ity will be considerably degraded.
Location of LED light
1. Are the transmitter and receiver batteries fully charged?
2. Is the remote antenna securely connected?
3. Is the distance between the transmitter and receiver too close?
4. When the procedure is carried out on the top of a desk or
bench top that is made from metal, the binding procedure
may not be successful.
If the bind process or range check is not successful,
check the following items:
Please note that when the model or model type is
changed in the transmitter, re-binding will be required.
Never fly the aircraft in Range Check mode.
Be sure that the failsafe settings are set in the
transmitter.
40 meters
各アンテナを互いに水平に設置すると、単一方
向の受信になるため、受信効率が低下します。
Bind plug
Binding terminal
Connecting
the battery to a
spare channel
RX battery
(sold separately)
Connection Chart
Switch harness
(sold separately)
Y-Harness
(sold separately)
RG631B Receiver
ORANGE
BROWN
RED
( )
( )
( )
ORANGE
BROWN
RED
( )
BROWN
( )
( )
RED
( )
( )
ORANGE
( )
Harness connection
Insert the connector,
taking adequate care
of the direction.
Sensor Installation
When connecting sensors, connect
a Y-Harness (sold separately) to the
(BIND/BATT/SENS) terminal.
Note that Sensors do not need
to be bound together with the
Transmitter and receiver.
C o a x i a l p a r t o f t h e
antenna can be bent
however, do not bend it
in a sharp angle. This
will damage the internal
antenna wires.
SENSOR
SENSOR
(sold separately)
Optional Remote Antenna RA01T/C
Preparation
XG6.indd 10
12/03/01 16:03
Summary of Contents for XG6
