Jonsered FR 13 Workshop Manual Download Page 61

Page: 61 / 68

ENGINE DOES NOT

AR
T

Starter and/or cable
connection defective

Discharged battery

Start relay no contact

Starter does not turn
engine over

Spark plug not sparking

Extremely burnt electrodes

Defective connection to
ignition cable

Short circuit in spark plug

Spark plug electrode
defective

Faulty fuel supply

Fuel tank empty

Fuel stop valve not
opening

No fuel to carburettor

No fuel from carburettor
(Spark plug dry)

Charge the battery

Replace the battery

No current to relay

Relay faulty
Replace relay

Check connections
Replace starter if necessary

Adjust electrode gap or
replace spark plug

Replace spark plug cover

Replace spark plug

Replace spark plug
electrode

Fill with fuel

No current to valve or
magnetic valve defective

Channel from fuel stop
valve blocked

Check cable connection or
replace valve

Clean channel with
compressed air

Fuel filter blocked

Change filter

Tank ventilator blocked

Clean or replace fuel cap

Fuel pump not working

Pump diaphragm broken

Impulse channel blocked

Fuel hoses blocked or
constricted

Clean or replace fuel hoses

Needles and diffuser jets
blocked

Clean carburettor with
compressed air

Replace diaphragm

Blow channel clear with
compressed air

Poor contacts on the
battery terminals

Blown fuse

Poor or no earth contact

Broken ignition lock

Microswitch for cutting
unit’s lifting lever defective
or in wrong position

Microswitch under seat
defective

Microswitch on gear stick
or hydraulic pedal
defective or in wrong
position (neutral position)

Clean and apply copper-
based lubricant

Replace fuse
Localise cause of fault

Clean, apply copper-based
lubricant

Check cable connections
or replace switch

Check cable connections
or replace switch
Adjust setting

Check cable connections
or replace switch

Check cable connections
or replace switch
Adjust setting

Summary of Contents for FR 13





































































Search results

Summary of Contents for FR 13

Reviews:

Related manuals for FR 13

Brands by name

Popular brands

Jonsered FR 13, Workshop Manual

Search results

Summary of Contents for FR 13

Reviews:

Related manuals for FR 13

Brands by name

Popular brands