Jonsered FR 13 Workshop Manual Download Page 20 | Manualshive

Page: 20 / 68

background image

18

– English

6011-008

6019-007

Design and Function

Outline sketch of the operation of the articulated
steering.

Steering

All riders in the FR series have articulated steering.
The force from the steering wheel is transferred to
the rear wagon via cables and a chain. This makes
steering the rider both easy and very precise. It
easily mows around all obstacles on the lawn.

The FR machines have steering columns with
bearings (1).

The turning circle is very small due to the
articulated steering; the uncut circle with full lock is
only 20-30 cm.

«
...
18
19
20
21
22
...
»

Summary of Contents for FR 13





































































Reviews:

No comments

Related manuals for FR 13

Brand: Agri-Fab Pages: 32

Brand: Dixon Pages: 36

Brand: Smithco Pages: 114

Brand: Yardworks Pages: 27

Brand: Ransomes Pages: 100

Brand: Talex Pages: 61

Brand: Yard-Man Pages: 8

Poulan Pro 961140016

Brand: Poulan Pro Pages: 2

Brand: Coopers of Stortford Pages: 13

Brand: ECLOZ Pages: 56

Brand: Jonsered Pages: 44

BOB-CAT 942311G

Brand: Schiller Grounds Care Pages: 72

Brand: Craftsman Pages: 56

Brand: GÜDE Pages: 66

Brand: GÜDE Pages: 84

Brand: GÜDE Pages: 88

430/36-2 Li-ION

Brand: GÜDE Pages: 82

Brand: GÜDE Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands