Jonsered FR 13 Workshop Manual Download Page 57

Page: 57 / 68

English –

6012-088

6012-089

Sharpening and Balancing Blades

• Remove the blades as described in the previous

section.

• Fix the blades in a vice and sharpen them with a

sharpening file.

WARNING!
Protect your hands with gloves
when working with the blades.

Balance the blades by:

• Attaching a mandrel, for example, horizontally in

the vice as shown.

• Thread the hole in the centre of the blade over

the mandrel and make sure that the blade is
equally weighted. The illustration shows a blade
that needs to be adjusted, it must be filed more
so as to attain the right balance (at the arrow).

• Assemble in the reverse order as described for

dismantling.

IMPORTANT INFORMATION

When the blades on the mulching unit
have been removed, the friction washer
located between the blade and nut must
be replaced.

Repair Instructions

Summary of Contents for FR 13





































































Search results

Summary of Contents for FR 13

Reviews:

Related manuals for FR 13

Brands by name

Popular brands

Jonsered FR 13, Workshop Manual

Search results

Summary of Contents for FR 13

Reviews:

Related manuals for FR 13

Brands by name

Popular brands