Jonsered FR 13 Workshop Manual Download Page 38 | Manualshive

Page: 38 / 68

background image

36

– English

6012-043

8009-133

8009-213

2

1

6012-042

Repair Instructions

Place a garage jack under the hydrostatic transmis-
sion and loosen its five attaching screws.

• Lower the garage jack and pull out the transmis-

sion.

• Fit the transmission in the reverse order.

• Make sure that after fitting, the brake and hydro-

static transmission cables are properly adjusted
(see Checking and Adjusting the Brake Cable,
Checking and Adjusting the Accelerator). Check
the oil level in the hydrostatic transmission and fill
as needed.
Check the neutral position contact’s setting on
machines with hydrostatic transmission.

Replacing the Hydrostatic Transmission
Shaft Seals

Seal Replacement, Ingoing Shaft

Remove the cooling fan, held in place by a circlip.
Remove the pulley from the ingoing shaft by pulling
it upwards and then removing the circlip under the
pulley.

• Clean the ingoing shaft and the area around the

seal from all dirt and rust.

• Insert a screwdriver between the seal and the

shaft and pry off the seal from the shaft housing
with a twisting motion.

IMPORTANT INFORMATION

The area around the seal must be abso-
lutely clean! If the hydrostatic transmis-
sion’s oil becomes contaminated by dirt it
can shorten the life of the transmission.

• Wrap insulating tape around the ingoing shaft in

order to protect the new seal from damage from
splines and grooves.
Begin wrapping from the bottom and continue
upwards over the shaft until the entire shaft is
wrapped in tape.

• Lubricate the shaft and the inside of the new

seal with grease so that the seal slips on
smoothly.

4

3

«
...
36
37
38
39
40
...
»

Summary of Contents for FR 13





































































Reviews:

No comments

Related manuals for FR 13

Brand: Murray Pages: 20

Brand: MTD Pages: 28

Brand: Alamo Pages: 168

Craftsman 917.250262

Brand: Sears Pages: 60

Brand: Worx Pages: 44

Brand: Gardena Pages: 18

Brand: DR Pages: 44

Brand: Yard-Man Pages: 20

Brand: Craftsman Pages: 60

Brand: Craftsman Pages: 56

Brand: Craftsman Pages: 60

Brand: Craftsman Pages: 240

Brand: Craftsman Pages: 60

Brand: Craftsman Pages: 56

Brand: Craftsman Pages: 60

Brand: Craftsman Pages: 60

Brand: Craftsman Pages: 60

Brand: Craftsman Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands