JLA D3030, Installation Manual

Page: 23 / 46

113161-14 01422 822282 19
ELECTRICAL SERVICE SPECIFICATIONS (PER DRYER)
SERVICE
VOLTAGE
PHASE
WIRE
SERVICE
OVEN
kW
APPROX. AMP DRAW CIRCUIT
BREAKER
60 Hz 50 Hz
REVERSING
208 3ø 3 20 61 — 80
220 3ø 3 17 50 51 70
240 3ø 3 20 54 — 70
380 3ø 3 17 31
—
40
460 3ø 3 18.5 26
—
40
480 3ø 3 20 27
—
40
208 3ø 3 24 72 — 90
220 3ø 3 20 58 59 80
240 3ø 3 24 63 — 80
380 3ø 3 20 36 — 50
460 3ø 3 22 31 — 40
480 3ø 3 24 32 — 50
575 3ø 3 24 27 — 40
208 3ø 3 30 88 — 125
220 3ø 3 26 73 75 100
240 3ø 3 30 78 — 100
380 3ø 3 26 45
—
60
460 3ø 3 28 38 — 50
480 3ø 3 30 39
—
50
575 3ø 3 30 33
—
50
230 3ø 3 18.5
—
53 70
240 3ø 3 20 — 56 80
380 3ø 4 or 3 17 — 29 40
400 3ø 4 or 3 18.5 — 30 40
416 3ø 4 or 3 20 — 31 40
230 3ø 3 22 — 61 80
240 3ø 3 24 — 65 90
380 3ø 4 or 3 20 — 34 50
400 3ø 4 or 3 22 — 35 50
416 3ø 4 or 3 24 — 37 50
440 3ø 4 or 3 20 — 29 40
230 3ø 3 28 — 76 100
240 3ø 3 30
—
80 125
380 3ø 4 or 3 26
—
43 60
400 3ø 4 or 3 28 — 44 60
416 3ø 4 or 3 30 — 45 60
3. Grounding
A ground (earth) connection must be provided and installed in accordance with state and local codes. In the
absence of these codes, grounding must conform to applicable requirements of the National Electrical Code
ANSI/NFPA NO. 70-LATEST EDITION, or in Canada, the installation must conform to applicable Canada
Standards: Canadian Electrical Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION. The ground
connection may be to a proven earth ground at the location service panel.
For added personal safety, when possible, it is suggested that a separate ground wire (size per local codes) be
connected from the ground connection of the dryer to a grounded cold water pipe.
DO NOT ground to a gas
pipe or hot water pipe . The grounded cold water pipe must have metal-to-metal connection ALL the way to
the electrical ground. If there are any nonmetallic interruptions, such as, a meter, pump, plastic, rubber, or
other insulating connectors, they
must be jumped out with a wire (size per local codes) and securely clamped
to bare metal at both ends.
IMPORTANT: For personal safety and proper operation, the dryer must be grounded.
Provisions are made for ground connection in each dryer at the electrical service connection area.
4. Electrical Connections
A wiring diagram is located inside the control box for connection data.
If local codes permit, power to the dryer can be made by the use of a flexible U.L. listed power cord/pigtail
(wire size
must conform to rating of dryer), or the dryer can be hard wired directly to the service breaker
panel. In both cases, a strain relief must be installed where the wiring enters the dryer.
Check your national and local code for breaker and wire size 1/7/15