JF FCT King Size 1260 Directions For Use Manual Download Page 78 | Manualshive

Page: 78 / 114

background image

6. WORKING IN THE FIELD

PIGB-206X-02 FCT1460 0614

- 78 -

BLOCKAGE IN THE MACHINE

Auger and feed intake section:

In case of blockage in the auger or feed intake section, immediately move the feed
intake to neutral position and reduce the number of revolutions.
Hereby the auger and the feed intake stop immediately, and you can obtain an
overview of the situation.

DANGER:

Do not approach the machine when the feed intake is in neutral
position and the rotor is rotating. Neutral position does NOT
guarantee that the feed intake will not start.

Now move the reverse system to reverse position at a low number of rpm (the push-
button  on  the  control  box).  Hereby  the  auger  is  lifted  and  the  feed  intake  runs
“backwards”  whereby  the  material  in  the  machine  is  reversed  out.  We  recommend
reversing slowly with the machine while the material is pushed out. This creates room
for the grass which is reversed out and leaves it as a regular “swath”.
After  reversing,  increase  to  normal  number  of  rpm.  Set  the  auger  and  feed  intake
section to normal feed in (toggle switch on the control box). It is important to have a
normal number of rpm, otherwise the chute or the rotor might be clogged up.

«
...
76
77
78
79
80
...
»

Summary of Contents for FCT King Size 1260



















































































































Reviews:

No comments

Related manuals for FCT King Size 1260

Brand: KaVo Pages: 16

Brand: Dana Design Pages: 20

Brand: Jackco Pages: 6

Brand: dbx Pages: 12

Brand: dbx Pages: 13

Brand: dbx Pages: 72

Brand: dbx Pages: 11

Brand: dbx Pages: 16

Brand: LA Audio Pages: 9

LSP400 LED Series

Brand: WE-EF Pages: 6

CIRCOLINA G10q T9

Brand: Life Pages: 2

ABS-Lock III-BE

Brand: ABS Pages: 8

WELCH LVS 600 T

Brand: Gardner Denver Pages: 68

Brand: ABB Pages: 112

Brand: Crosley Pages: 6

Brand: Gambro Pages: 273

Brand: Cutler-Hammer Pages: 45

Brand: NSF Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands