JF FCT King Size 1260 Directions For Use Manual Download Page 26 | Manualshive

Page: 26 / 114

background image

2. CONNECTION TO TRACTOR

PIGB-206X-02 FCT1460 0614

- 26 -

CONNECTION OF ELECTRIC SYSTEM

Fig. 2-2

The machine is equipped with full electronic operation of all the machine’s hydraulic
functions. The electronic operation consists of 2 units:



A control unit mounted on the machine together with the hydraulic system.
This unit activates the hydraulic valves.



A control box for operation of the hydraulic functions. This can be placed on

the right arm rest in the tractor cabin, allowing the driver easy access to it
while driving in the field.

The control box is equipped with detachable fittings which can be fastened in the
tractor cabin with screws, and it can subsequently be dismounted without tools.

The plug for the power supply is connected to a socket in the tractor cabin. This
should supply 12 V and allow minimum 15 A. If the tractor does not have the same
plug you should contact your dealer and get an adaptor.

IMPORTANT:

When the machine is parked the control box should be placed in the
chute support on the drawbar.

Fig. 2-2

«
...
24
25
26
27
28
...
»

Summary of Contents for FCT King Size 1260



















































































































Reviews:

No comments

Related manuals for FCT King Size 1260

Brand: T-Drill Pages: 75

Brand: Zeiss Pages: 38

Brand: Oberheim Pages: 40

Brand: Raymarine Pages: 90

Brand: Danelec Pages: 67

Crouse-hinds series

Brand: Eaton Pages: 32

Brand: Gamry Instruments Pages: 69

Brand: Gamry Instruments Pages: 30

Brand: Gamry Instruments Pages: 88

Brand: Rayger Pages: 2

Brand: Gatekeeper Pages: 8

Bure Rise & Go DB 56-309

Brand: Gate Pages: 8

Brand: Madsen Pages: 206

Brand: Rational Pages: 60

Brand: TANACOM Pages: 27

Brand: iBACheck Pages: 2

Marathon Multi600

Brand: Saeyang Pages: 21

Brand: S&C Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands