JF FCT King Size 1260 Directions For Use Manual Download Page 4

Page: 4 / 114

PIGB-206X-02 FCT1460 0614

- 4 -

CONTENTS

FOREWORD ....................................................................................................................... 3

CONTENTS ......................................................................................................................... 4

1. INTRODUCTION ............................................................................................................. 7

INTENDED USE ................................................................................................. 7

PERFORMANCE ................................................................................................ 8

SAFETY ............................................................................................................ 10

Definitions ............................................................................................ 11

General safety instructions ................................................................... 11

Locking of guards ................................................................................. 13

Choice of tractor ................................................................................... 13

Connection and disconnection ............................................................. 14

Adjustment ........................................................................................... 15

Transport .............................................................................................. 16

Working ................................................................................................ 17

Parking ................................................................................................. 17

Greasing .............................................................................................. 17

Grinding ............................................................................................... 18

Maintenance ........................................................................................ 19

Replacement of wearing parts ............................................................. 19

Safety decals ....................................................................................... 21

TECHNICAL DATA ........................................................................................... 23

2. CONNECTION TO TRACTOR ...................................................................................... 24

THE HYDRAULIC SYSTEM ............................................................................. 24

Hydraulic connection ............................................................................ 24

Bypass valve ........................................................................................ 25

Connection of electric system .............................................................. 26

ELECTRO-HYDRAULIC CONTROL ................................................................ 27

Functions ............................................................................................. 28

DRAWBAR AND PTO DRIVE SHAFT .............................................................. 31

Shortening of the PTO drive shaft ........................................................ 32

Friction clutch ....................................................................................... 32

3. MOUNTING OF EQUIPMENT ....................................................................................... 33

HITCH FOR TRAILER ...................................................................................... 33

Combi-hitch .......................................................................................... 33

Hydraulic hitch hook (Auto-hitch) ......................................................... 34

PICK-UP ........................................................................................................... 35

TRANSPORT CONVERSION .......................................................................... 38

FITTING CHUTES ............................................................................................ 39

Chute turning ....................................................................................... 39

Standard chute ..................................................................................... 41

Collapsible chute .................................................................................. 41

Chute for parallel operation .................................................................. 42

Summary of Contents for FCT King Size 1260



















































































































Search results

Summary of Contents for FCT King Size 1260

Reviews:

Related manuals for FCT King Size 1260

Brands by name

Popular brands

JF FCT King Size 1260, Directions For Use Manual

Search results

Summary of Contents for FCT King Size 1260

Reviews:

Related manuals for FCT King Size 1260

Brands by name

Popular brands