JF FCT King Size 1260 Directions For Use Manual Download Page 42

Page: 42 / 114

3. MOUNTING OF EQUIPMENT

PIGB-206X-02 FCT1460 0614

- 42 -

DANGER:

The chute is more than 4 m high. Be aware of high-voltage lines.
Keep a safe distance away from high voltage lines.

WARNING:

Make sure that persons keep a safe distance from the machine when
moving the chute.

The hydraulic functions must be operated from the

tractor.

IMPORTANT:

Be careful not to hit the tractor cab.

IMPORTANT:

Do not move the drawbar while the chute is resting on the stand.

IMPORTANT:

Do not turn the chute while it is resting on the stand.

IMPORTANT:

The chute must always rest on the stand during transport. This is

partly due to the Road Traffic Act and also because the
chute/delivery chute may get damaged, for instance if you drive fast
on uneven ground.

CHUTE FOR PARALLEL OPERATION

Fig. 3-18

The machine can be fitted with a chute that has a transport height of 4.4 metres. This

chute cannot be folded for transport.

Fig. 3-18

-1

Summary of Contents for FCT King Size 1260



















































































































Search results

Summary of Contents for FCT King Size 1260

Reviews:

Related manuals for FCT King Size 1260

Brands by name

Popular brands

JF FCT King Size 1260, Directions For Use Manual

Search results

Summary of Contents for FCT King Size 1260

Reviews:

Related manuals for FCT King Size 1260

Brands by name

Popular brands